OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
Reproduction of the original vent window rubber seals for 1955-57 Chevrolet two and four door sedan, wagon and sedan delivery models. This weatherstrip is manufactured in quality EPDM rubber that offers a superb fitment and...
1955-57 Bel Air, 150, 210, Nomad; Vent Window Seals; 2 & 4 Door Hardtop, Convertible; Pair
Vent window rubber seals for 1955-57 Chevrolet two and four door hardtop, convertible and Nomad models. Set includes two "C" weatherstrip pieces and two vertical weatherstrip pieces which is designed to replace both RH and LH...
1956-57 Bel Air, 150, 210, Chieftain; Back Window Glass Weatherstrip Seal; 2 & 4 Door; Sedan,
Reproduction weatherstripping that surrounds the back window glass channel on 1956-57 Chevrolet and Pontiac 2 and 4 door sedan models as listed below. After years of exposure to the sun and weather, this weatherstrip usually...
1937-80 GM, 1961-64 Impala, 1964-72 El Camino; Gas Door Bumpers; 1937-58 1-prong Door Bumpers; Pair
Correct reproduction rubber bumper for various GM applications. Fits: 1937-1958 GM full size vehicle door bumper, single prong style, front or rear. 1961-64 full size and 1964-72 El Camino gas filler door. Keeps the door from...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
1955-57 Chevy Bel Air, 150, 210; Upper Window Stop Set; Inside Door; 2 & 4 Door; 4 Piece Set
Reproduction window stops for 1955-57 Bel Air, 210 and 150 Chevrolet 2 and 4 door, Nomad and convertible models. Used to adjust the UP travel of the window. Manufactured in EPDM rubber for long-lasting dependability. Set of 4...
1957-59 Chevrolet Speedometer Cable Grommet
This grommet mounts on the firewall where the speedometer cable runs through it. Manufactured in automotive grade molded rubber. Replaces OE # 3781684.
1958-59 Impala, Bel Air, Biscayne, El Camino; Rear Gas Filler Door Bumpers; Pair
Correct reproduction of the original gas filler door rubber bumper for use with 1958-59 Impala, Bel Air, Biscayne, and El Camino models. Each bumper is manufactured in EPDM rubber to original factory specifications. Keeps the...
1957-70 Buick, Cadillac, Chevy, Pontiac, Oldmobile; Trunk Weatherstrip; Various Full Size Models
Reproduction of the original trunk weatherstrip manufactured in the correct configuration. Prevent water damage in your trunk area by replacing the worn and damaged weatherstrip with this authentic reproduction. The soft...
1957 Chevy Bel Air, 150, 210; Weatherstrip Kit; 2 Door; Sedan
Complete weatherstrip set. Each weatherstrip is manufactured in quality EPDM material to factory specifications ensuring proper fit and function once installed. This kit will replace every major weatherstrip and include the...
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
Reproduction trunk weatherstrip manufactured in the correct configuration. Prevent water damage in your trunk area by replacing the worn and damaged weatherstrip with this authentic reproduction. The soft extruded...
1956-57; Bel Air, 210, Chieftain; Rear Door Frame Weatherstrip; 4 Door; Hardtop; RH and LH; Pair
Reproduction of the original rear door frame weatherstrips for 1956-57 Chevrolet four door hardtop models. Each weatherstrip is manufactured to replicate the original for an authentic fit and appearance. Create a...
Reproduction of the original style door frame weatherstripping designned for use with 1955-57 Chevrolet and Pontiac hardtop and convertible 2 door models. Create a weather-tight seal between the front doors and the body....
1949-58 Bel Air, 150, 210, Nomad, Impala, Bel Air, Biscayne; Door Bumpers; Pair; Various Models
Reproduction door rubber bumpers for 1949-1958 Chevrolet Bel Air, 150, 210, Impala, Bel Air, Biscayne, and various station wagon models. Designed to help keep your door aligned and in the correct position. Each bumper...
1955-57 Chevy Bel Air, 150, 210, Nomad; Upper Trunk lid, 1955-59 Rear License Plate Bumpers; Pair
Correct reproduction of the rubber bumper for the upper trunk on 1955-57 Chevrolet Bel Air, 150, 210, Nomad cars and the rear license plate on all 1955-59 Impala. Bel Air, Biscayne, El Camino, and station wagon models. Sold...
1982-04 GM; Hood Adjustment Rubber Bumper & Bolt; 1" Diameter; Each; Various Models
Replace your original rubber hood adjuster stoppers with a correctly configured reproduction hood adjustment bumper. This part replace the adjuster bolt and the rubber bumper for a complete bolt-on replacement of the...
1955-57 Chevrolet Bel Air, 150, 210; Spare Tire Well Plug; Each
Reproduction of the original spare tire body plug designed for use with 1955-57 Chevrolet models. Each rubber plug is manufactured in EPDM rubber replicating the original configuration. Sold individually. Use as required.
1955-81 Chevrolet, GMC, Pontiac; Air Cleaner Lid Rubber Seal; 59" Long x 5/16" Wide
Reproduction air cleaner lid seal for a variety of GM car and truck models as listed. Designed to seal the area between the lid and the base offering a tight seal for the air cleaner on models that required this seal.
1957 Chevy Bel Air, 150, 210, Nomad; Rear Bumper to Body Seal
Reproduction of the original rear bumper to body seal designed for use on 1957 Chevrolet Tr-Five models. Each body seal is manufactured to original factory specifications. Features the correct length and shape for an...
1957 Chevy Bel Air, 150, 210, Nomad; Steering Column Floor Seal; with Auto Trans & Manual Brakes
Reproduction steering column floor seal for 1955 Chevrolet models equipped with automatic transmission and manual brakes. Manufactured from plastic as original, this seal secures the front edge of the carpet in place and...
1957 Chevrolet 150, 210, Bel Air; Steering Column Floor Seal; with Manual Trans
Reproduction steering column floor seal for 1957 Chevrolet models equipped with manual transmission. Manufactured from plastic as original, this seal secures the front edge of the carpet in place and maintains a...
1956 & 1958 Chevy Bel Air, 150, 210, Impala, Biscayne; Rear Bumper to Body Seal Weatherstrip
Reproduction of the original rear bumper to body seal designed for 1956 and 1958 Chevrolet full size passenger car models. Each body seal is manufactured to factory specifications from molded EPDM rubber.
1988-00 Chevrolet, GMC C/K GMT400 Pickup, SUV; Tailgate Rubber Bumper
Reproduction tailgate rubber bumper for 1988-1998 Chevrolet and GMC C/K GMT400 Pickup, 1999-2000 C/K 2500/3500 pickup carryover models, 1992-1999 Suburban, 1992-94 Full Size Blazer, and 1992-2000 Tahoe, Yukon, and Escalade...
1955-57 Chevy Bel Air, 150, 210, Nomad; Dome Lamp Harness Grommet; Hardtop
Molded rubber reproduction dome lamp harness grommet for 1955-57 Chevy Bel Air, 150, 210, and Nomad hardtop models. This grommet prevents wire damage and measures 2-1/4" OD x 1/4" ID and fits a 1-1/2" hole.
1987-2016 GM; Rear Trunk Lid Access Hole Plug; Each; Various Models
Reproduction trunk lid drain hole plug for 1987-2016 GM vehicles including 1991-96 Impala and Caprice models. Manufactured from molded rubber as original, these install on the underside of the trunk lid. Measures 9/165"...
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1955-90 Buick, Chevrolet, Pontiac, Oldsmobile; Door Lock Gasket; Each; Various Models
Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...
1958-77 Buick, Chevy, Olds, Pontiac; Hood Adjust Bumper and Screw Set; Various Models
Reproduction hood adjustment bumpers for various 1958-77 GM models including 1967-69 Camaro and Firebird models. These 7/8" OD reproduction stoppers and screws are manufactured to original specifications to replace the worn...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1955-1976 Glove Box Door Arm Rubber Stopper
Reproduction of the original glove box door arm rubber stopper designed for use on various GM models. Eliminate the rattling and looseness of the glove box door by simply replacing the worn out or missing rubber glove box...
1980-2016 GM; Outer Hood Adjust Rubber Bumper; Each; Various Models
Reproduction of the original molded rubber hood adjustment bumper located on the outer hood for various 1980-2002 GM models. This reproduction molded rubber bumper is manufactured to original specifications for an authentic...
1955-72 GM; Lower Control Arm Bumpers; Polyurethane; Black; Pair
Polyurethane lower control arm bumper stops are guaranteed to last longer and perform better than O.E.M. rubber stops. Cushions impact between suspension components preventing excessive damage. Sold as a pair. 1 pair required...
Sealstrip Glass Setting Tape; 10 Foot Roll; 1/32" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1957-58 Chevrolet Bel Air, 150, 210, Nomad; Radiator Core Support Wiring Grommet
High-quality reproduction radiator core grommet designed for 1957-58 Chevrolet passenger car models. This grommet routes and protects the wiring harness as it passes through the radiator core support, preventing abrasion and...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1951-72 Buick, Chevrolet, Pontiac, Oldsmobile; Convertible Power Top Motor Mounting Grommet; Each
Reproduction of the original rubber mounting/insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a damper...
1958-75 Clutch Bellcrank Felt Seals ; Pair
OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...
Reproduction headlight housing to fender gaskets designed for 1947-57 Chevrolet and GMC truck models, as well as 1941-57 GM passenger car applications. Each gasket is manufactured from high quality die stamped rubber and...
Door, Vent, Quarter Glass; Sealstrip Glass Setting Tape;10 Foot Roll; 1/16" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1955-58 GM Full Size; Vent Window Bumper Stops; Upper; Pair
Reproductions of the original upper vent window bumpers designed for use on 1955-58 GM Full Size models. Upper vent window bumpers are manufactured to replicate the original design and fit. Includes molded rubber design with...
Sealstrip Glass Setting Tape ; 10 Foot Roll ; 3/64" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1956-60 Bel Air, 150, 210, Nomad, Impala, Bel Air, El Camino; Firewall Wire Harness Grommet; Each
Reproduction of the original firewall wire harness grommet for use with various 1956-60 Chevy Bel Air, 150, 210, Nomad, El Camino, Impala, Biscayne, and various other models including station wagons. This grommet is...
1955-79 Outer Door Handle Push Button O-Ring Gasket ; Each
This door handle O-ring is one of the most overlooked replacement parts on any vehicle. The O-ring inserts onto the outer door handle push button and eliminates rattling and wear between the handle and the push button....
1967-69 Camaro, Firebird; Plastic Clip Set; Radiator Support To Hood Seal; 9 Piece Set
Reproduction of the radiator support to hood seal clip set designed for 1967-69 Camaro and Firebird models with air conditioning. Each clip is injection molded to original specifications. Clips are designed to hold the hood...
1938-91 GM; Consol & Glove Box Rubber Stoppers; Fits 1/4" Hole; Pair
Eliminate the rattling and looseness of the glove box or console door by simply replacing worn out or missing rubber stoppers with these high quality reproduction rubber stoppers. Designed for use with a variety of 1938-1991...
1941-76 Mohair Window Channel Liner ; 2-5/8" wide x 8" long
When it comes to relining the door and quarter window channels, this Mohair liner material is what you'll need. A finely textured mohair lining material with a rubberized backing. Inside the door, there are "U" shaped...
1977-2005 Buick, Chevy, Olds, Pontiac; Compartment Lid Rubber Bumper; Front or Rear; Each
Reproduction of the original rear compartment lid rubber stopper needed to prevent the rear compartment lid from slamming against the body. Each rubber bumper is manufactured in quality EPDM rubber that replicates the...
1955-76 Chevrolet Bel Air, 150, 210, Impala, Caprice; Fender Skirt Rubber Seal ; 120" Long; OER
Reproduction fender or quarter panel skirt rubber seal for various 1955-76 Chevrolet models. Manufactured to correct dimensions from quality EDPM rubber that replicates the original in fitment and appearance. Measures 120"...
1957 Chevrolet Bel Air, 150, 210, Nomad; Hood To Cowl Seal; 2 & 4 Door, Hardtop, & Convertible
Reproduction of the original hood to cowl weatherstrip seal designed to keep water, dirt, and other debris out of your engine compartment. This reproduction is manufactured in the correct configuration allowing the seal to...
1941-76 Mohair Window Channel Liner ; 1-5/8" Wide x 8" Long x 1/16" Thick
When it comes to relining the door and quarter window channels, this Mohair liner material is what you'll need. A finely textured mohair lining material with a rubberized backing. Inside the door, there are "U" shaped...