Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
1961-83 GM; Seat Back Rubber Bumper Stopper; Various Uses & Models; Each
Correct replacement of the rubber bumper for use on various GM models. This rubber stopper will help insure that your seat/hood is aligned properly. Sold individually. Use as required per vehicle. 1-3/16" long, diameter of...
1982-04 GM; Hood Adjustment Rubber Bumper & Bolt; 1" Diameter; Each; Various Models
Replace your original rubber hood adjuster stoppers with a correctly configured reproduction hood adjustment bumper. This part replace the adjuster bolt and the rubber bumper for a complete bolt-on replacement of the...
1982-2012 GM Fuel Door; Door Pull Handle; Hood Stop; Sunroof. Rubber Bumper; Each; Various Models
Reproduction of the original style rubber bumper that fits a wide variety of 1982-2012 GM models and applications. Can be used for the fuel door, front and rear door pull handle, hood stop bumper, and sunroof control arm....
1980-2016 GM; Outer Hood Adjust Rubber Bumper; Each; Various Models
Reproduction of the original molded rubber hood adjustment bumper located on the outer hood for various 1980-2002 GM models. This reproduction molded rubber bumper is manufactured to original specifications for an authentic...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
Reproduction rubber bumper for various GM applications. Each bumper is manufactured in EPDM rubber to factory specifications replicating the original in design and fitment. This bumper was used for various applications...
1938-91 GM; Consol & Glove Box Rubber Stoppers; Fits 1/4" Hole; Pair
Eliminate the rattling and looseness of the glove box or console door by simply replacing worn out or missing rubber stoppers with these high quality reproduction rubber stoppers. Designed for use with a variety of 1938-1991...
1954-1981 GM; Hood Adjustor Rubber Bumper & Stud; Various GM Cars & Trucks
Reproduction 5/16-18 x 1-1/2" hood bumper. Includes correctly threaded stud with a 1" diameter x 1/2" tall round rubber top. Helps keep the hood aligned when installed. Can be adjusted higher or lower. 2 hood adjust bumpers...
1977-2005 Buick, Chevy, Olds, Pontiac; Compartment Lid Rubber Bumper; Front or Rear; Each
Reproduction of the original rear compartment lid rubber stopper needed to prevent the rear compartment lid from slamming against the body. Each rubber bumper is manufactured in quality EPDM rubber that replicates the...
Reproduction of the original rubber stopper designed for use on the upper door section of the various GM models listed below. Each rubber stopper is manufactured to replicate the original in fitment and appearance. This...
1958-72 Buick, Chevy, Olds, Pontiac; Trunk Lid Rubber Stopper; Each; Various Models
Correct OER® reproduction of the original trunk lid rubber bumpers designed for use with various 1958-72 GM models. Manufactured to factory specifications including correct stud to adjust for height concerns. Eliminates...
1970-87 Buick, Chevrolet, Olds, Pontiac; Upper Control Arm Bumper;Various Models; Each
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. Each upper control arm bumper is manufactured in the correct dimension using quality hardened EPDM rubber ensuring a quality reproduction...