Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
1978-85 Buick, Chevrolet Pontiac, Oldsmobile; T Top Handle Set; Chrome; RH & LH; Pair
OER reproduction of the original T-Top handles designed for use on various 1978-85 GM vehicles. Each handle is manufactured in quality die-cast zinc and finished in bright polished chrome for an authentic factory appearance....
Reproduction of the original GM frame body mount cushion for various 197-96 GM models. Each body mount is produced using correct compression molded S.B.R. that replicates the original in quality and fitment. 1977-79 Nova/GM...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1977-2005 Buick, Chevy, Pontiac, Oldsmobile;;Hood Latch Assembly; Various Models
Reproduction hood latch assembly for various 1977-2005 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models as listed below. Each latch is designed as a direct replacement for the worn or inoperative original....
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
1976-88 Buick, Chevy, Pontiac, Olds; Outer Door Handle; Chrome; Front or Rear; LH; Various Models
Reproduction of the original style front or rear outer door handle designed for use with various 1976-88 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each handle is manufactured to correct factory...
1977-87 Chevrolet Caprice, Impala, 1977-86 El Camino, Monte Carlo; Hood Latch Pop-Up Spring
Replacement hood latch pop-up spring for multiple 1977-87 GM applications including 1977-87 Chevrolet Caprice, Impala and 1977-86 El Camino, Monte Carlo models. This is the spring that mounts to the hood latch and pops the...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a set of 10, refer to part...
Bumper Bolt with Stainless Steel Head; Zinc Plated; 7 /16"-14 x 1" Bolt with Hex Nut
Reproduction bumper bolt with hex nut manufactured in zinc plated material offering an authentic appearance and fitment. Measures 7/16" -14 x 1" and features a stainless steel cap. Head diameter 31/32". Each bolt will replace...
1970-2002 GM; Hood Insulation Fastener; Each
Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...