1970-81 Camaro / Firebird; Side Hood Rubber Stopper
Correct replacement hood rubber stopper including correct configuration and design. Manufactured in rubber material same as original. Sold individually. 4 required per vehicle.
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1968-81 Trunk Lid Bumper On Lid; 7/8" Diameter, 1/2" thick
Correct replacement bumper to eliminate the lid from touching the body and causing unnecessary damage. Dimensions: Body Diameter: 7/8" Body Height: 1/2" Mounting hole diameter: 7/32" Overall Height: 13/16" {specs} {fitment}
1958-84 GM; Outer Rear Hood Rubber Stoppers; Pair; Various Models
Reproduction outer rear hood bumpers for various GM models. Each bumper is manufactured to quality EPDM rubber compound and matches the original in dimensions allowing proper fitment. Sold in pairs. Use as required Buick...
1968-81 Camaro, Impala, Firebird; Door Glass Guide Stop Bumpers; Pair; Various GM
Reproduction of the original door glass guide stop bumpers designed for use with various 1968-81 General Motors vehicles. These glass guide stops are required for proper door glass alignment. Commonly damaged during removal...
1970-81 Camaro Rubber Stopper Kit
The stoppers will help keep your panels in the correct alignment positions. The kit includes all of the correct rubber stoppers needed for the doors, hood, trunk lid, console, and glove box. OER® recommends replacing all...
1970-81 Camaro / Firebird Locking Rod To Inner Panel Silencer, 2 Piece Set
Reproduction of the of the original door lock rod rubber silencer designed for use on all 1970-81 Camaro and Firebird models. This rubber piece attaches to the inner door and the lock rod unit passes thru this molded rubber...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1962-81 GM; Glove Box Door Arm Rubber Bumper
OER® reproduction of the original glove box door arm rubber bumper designed for use with various 1962-81 GM models. This rubber bumper is manufactured in EPDM rubber to the original factory configuration. Was installed on...
1938-91 GM; Consol & Glove Box Rubber Stoppers; Fits 1/4" Hole; Pair
Eliminate the rattling and looseness of the glove box or console door by simply replacing worn out or missing rubber stoppers with these high quality reproduction rubber stoppers. Designed for use with a variety of 1938-1991...
1970-90 GM; Lower Door Window Stop Bumper; Each
Correct reproduction rubber stop bumper designed to keep the door glass from rolling down beyond the required travel point. Each stopper is manufactures from quality EPDM rubber and features a press fit retaining tab for easy...
1970-81 Camaro, Firebird; Door Window Stop; Each
Reproduction door window stop for 1970-81 models. Replace your damaged original door window stoppers with this correctly plated and rubber coated reproduction. Manufactured from high quality die stamped steel. Includes clear...
1965-92 Outer Door Rubber Bumper; Various Models
Reproduction of the original rubber stopper designed for use on the upper door section of the various GM models listed below. Each rubber stopper is manufactured to replicate the original in fitment and appearance. This...
1970-81 Camaro; Rear Hood Rubber Stopper ; Each
Correct reproduction rubber bumper for 1970-81 Camaro models. This bumper is manufactured in quality EPDM rubber replicating the original in quality and design. Fits on the rear outer section. The hood rests on the bumper...
1970-87 Buick, Chevrolet, Olds, Pontiac; Upper Control Arm Bumper;Various Models; Each
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. Each upper control arm bumper is manufactured in the correct dimension using quality hardened EPDM rubber ensuring a quality reproduction...
Reproduction rear axle compression bumper which attaches to the body and keeps the rear axle from bottoming out. Manufactured using hard rubber material with molded in stud for mounting. This is the second design bumper that...