1970-81 Rear Spring Shackle Bushing ; Camaro, Firebird, Nova, X-Body
Replace your cracked or worn out original rear spring shackle bushings and bring your rear suspension back to original factory ride specifications. Each bushing is designed and manufactured to replicate the original in...
1967-69 Camaro, Firebird, 1968-79 Nova; Mono Rear Leaf Springs; Pair; Made in the USA!
Reproduction of the original mono rear leaf springs designed for use with 1967-69 Camaro, Firebird models, and 1968-79 Chevy II, Nova, and X-body models. Each leaf spring is manufactured to factory specifications and...
Replace the sagging leaf springs on your classic GM vehicle with this high quality set produced by OER. These replacement rear leaf springs are engineered to directly replace the original multi leaf spring set while...
1959-81 GM; Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for use on various GM models. Manufactured from durable EPDM rubber, this spacer was originally installed to correct uneven ride height on vehicles that did not...
1970-2005 GM Cars, Trucks; Upper Ball Joint with Hardware; Various Models
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
Reproduction rear leaf spring shackle for 1970-79 Chevy II/Nova, GM X-Body, and 1970-81 Camaro, Firebird models. Each shackle eplaces the old or worn out original hardware and bushings with a quality reproduction. Includes...
1975-79 X-body Nova; Front End Rebuild Kit; With Inner and Outer Tie Rod Ends
Comprehensive assortment of front end parts designed to renew worn out original front suspension components. Each component is manufactured by the original GM supplier or equivalent. Be sure you install what the factory...
1975-79 Nova, Ventura, Omega, Apollo; Front End Suspension Rebuild Kit; with Outer Tie Rod Ends Only
This set includes a comprehensive assortment of front end components engineered to renew worn out suspension parts. Designed to restore proper handling, improve steering response, and reduce uneven front tire wear, this front...
1971-2005 GM; Lower Control Arm Bushing; Passenger Car and Truck; Varius Models; Each
Reproduction control arm bushing for the lower control arm on various 1971-05 GM and various other models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning or...
Front sway bar for various 1964-1981 Buick, Chevrolet, Pontiac, and Oldsmobile models equipped with a 1-1/8" diameter bar. This versatile sway bar fits a wide range of GM vehicles including Buick Skylark and Special,...
1970-81 Camaro, Firebird; Front Sway Bar; with WS6 Suspension; 1-1/4"
Reproduction of the original factory style 1-1/4" front sway bar designed for use with 1970-81 Camaro and Firebird models with WS6 suspension. This silver zinc plated sway bar is compatible with factory mounting brackets....
Front sway bar for various 1964-1981 Buick, Chevrolet, Pontiac, and Oldsmobile models equipped with a 1-1/4" diameter bar. Engineered to significantly reduce body roll, under steer, and over steer during cornering, this...
1970-81 Camaro, Firebird; Front Sway Bar; 1-1/16"; High Performance; LS5, LS6
Reproduction of the original factory style 1-1/16" front sway bar designed for use with 1970-81 Camaro and Firebird models including various 1964-72 Chevrolet, Buick, Olds, and Pontiac models with high performance suspension...
1968-81 Camaro, Firebird, Nova; Rear Sway Bar Anchor Plate Bolt; 7/16"-20 X 1-5/16"
Bolt and nut used to attach the rear sway bar bracket to the lower anchor plate and leaf spring perch. This case hardened bolt measures 7/16"-20 x 1-5/16" and is designed for models equipped with standard suspension. 4 bolts...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1970-81 Rear Sway Bar Bracket ; 1970-81 F-Body, 1970-79 X-Body ; Various Models
This OER® reproduction of the original rear sway bar bracket manufactured from high grade stamped steel to original specifications. Sway bar brackets hold the sway bar bushings to the frame and secures the rear sway bar...
1968-69 Camaro, Firebird, 1968-79 Nova; Multi Leaf Spring Pad Set; 4 Piece Set
Each pad is designed to insulate the contact area between the leaf spring and the mounting plate, preventing metal to metal contact that can lead to noise, vibration, and premature wear. These pads help maintain proper...
1962-87 Buick, Chevrolet, Pontiac, Olds; Ball Joint Rivet Bolt Set; 24 Piece Set; Various Models
This rivet style bolt set attaches the ball joint to the upper control arm while providing the authentic appearance of factory installed rivets. Each bolt features a serrated locking rivet style head that prevents spinning...
Includes all the components needed to replace the original bushings and hardware. One set services only one side of the vehicle, with two sets required per vehicle. Features a 2" spacer for proper installation and alignment....
1967-81 Camaro, Firebird, Nova, GM X-Body; Rear Spring Eye Bracket Bolt Set; 6 Piece Set
Quality reproduction rear spring eye bracket bolts designed to mount the leaf spring front eye bracket. Each bolt is case hardened for exceptional durability, strength, and long lasting performance. An ideal replacement for...
1960-88 Various GM Vehicles Camaro, Impala, Cutlass; Front Sway/Stabilizer Bar; Bushing 1-1/4"
New 1-1/4" sway bar bushing for use with original bracket various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment. Replace the old...
1960-96 Various GM Vehicles Camaro, Cutlass, Impala; Front Sway/Stabilizer Bar; Bushing WS6; 13/16"
New 13/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
New 15/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
Reproduction sway bar end link for various 1955-2005 GM car and truck models. Replaces the sway bar end links to eliminate issues associated with worn out links. Each sway bar link includes rubber bushings. Includes 4...
1967-81 Camaro Z/28, Firebird, Nova; Rear Leaf Springs; 4 Leaf; Spring Rate 126 lbs; Pair
Reproduction of the original 4 leaf rear leaf springs designed for use with 1967-1969 Camaro Z28 (302), 1968-1981 Firebird 400 and other performance models, as well as Chevy II, Nova, and various GM X body models originally...
Reproduction molded rubber front coil spring insulator designed to mount between the coil spring and the frame on various 1949-2002 vehicles. This insulator prevents metal to metal contact, reducing noise, vibration, and...
Bolt and nut designed to attach the rear sway bar bracket to the lower anchor plate and leaf spring perch. This case hardened fastener measures 7/16"-20 x 1-15/16" and is engineered specifically for models equipped with the...
1970-05 GM Cars / Trucks; Lower Ball Joint (Standard Size); Thread: 9/16"
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
These sway bars are engineered to reduce body roll, under steer, and over steer during cornering, resulting in noticeably improved handling, stability, and overall vehicle control. Designed to deliver better road feel without...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
1971-96 GM; Upper Control Arm Bushing; Various Models; Pair
Reproduction style upper control arm bushing designed for various 1971-96 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1974-78 Mustang II; Front Sway Bar Kit; 3/4" ; 43-1/4" Wide; for Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks equipped with standard width crossmember Mustang II front suspension systems. This sway bar is engineered to reduce body roll, under steer, and over steer during...
1973-91 Buick, Chevy, GMC, Olds, Pontiac; Sway Bar Bracket; Each; Various Models
OER® reproduction of the original style "U" shaped sway bar bushing clamp designed for use with various GM models. This bracket is manufactured from stamped steel and used to hold the inner sway bar bushings and the sway...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
1967-81 Buick, Chevrolet, Oldsmobile, Pontiac; Rear Axle Pinion Bumper; Each; Various Models
This reproduction rear axle pinion bumper is designed for various GM models and manufactured from high quality molded rubber with an integrated steel bracket formed in the correct OE configuration. Built to replicate the...
1970-05 GM Cars / Trucks; Lower Ball Joint (.0025 Oversize)
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1967-81 Camaro, Firebird, Nova, GM X-Body; Spring Eye Bracket Nut Kit; 6 Piece Set; Various Models
Quality reproduction spring eye bracket nut kit to mount the leaf spring front eye bracket. Manufactured to high strength specifications, each nut is designed to provide secure, long lasting fastening when paired with the...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4" to 4" inclusive. These heat treated washers are for general purpose and structural use. For use...
1967-81 Camaro, Firebird, Nova, GM X-Body; Rear Spring Eye Bracket Nut; Each
This is a quality reproduction of the original style spring eye bracket nut used to mount the leaf spring front eye bracket. Manufactured to high strength specifications, each nut is designed to provide secure, long lasting...
1968-79 Camaro, Firebird, Nova, X Body; Rear Leaf Spring Pad; Multi Leaf; Upper & Lower; Each
Reproduction of the original multi leaf, upper and lower rear leaf spring pad designed for use on various GM models. Each pad is manufactured to OE specifications in EPDM rubber compound. Always replace the rear leaf spring...
1970-81 Camaro, Firebird, 1975-79 Nova; Rear Leaf Spring Installation Set; Multi-Leaf
Reproduction of the original and complete rear leaf spring installation kit designed for use on 1970-81 various GM vehicles equipped with multi-leaf rear springs including 1970-81 Camaro, Firebird, 1975-79 GM X-body models as...
1962-81 GM; Rear Leaf Spring Front Eye Bracket Bolt ; Each; Various Models
Quality reproduction of the original rear spring eye bracket bolt designed to mount the leaf spring front eye bracket. Each bolt is case hardened for exceptional durability, strength, and long lasting performance. An ideal...
1961-1994 GM, Ford; Upper Control Arm Bushing; Front or Rear; Various Applications
Reproduction of the original control arm bushing designed for use on the the upper control arm for various 1961-1994 GM and Ford models. Manufactured in steel clad rubber that replicates the original control arm bushing in...
1971-2005 GM; Rear Lower Control Arm Bushing; Each; Various Models
Reproduction control arm bushing for the lower control arm on various 1971-2005 GM models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning or going over...
1969-83 GM; Front Sway Bar Bushing; 1" Inner Diameter; Each
Reproduction front sway bar bushing for various GM models. This rubber bushing includes a 1" diameter hole and is installed on the the front sway bar on most models that included a heavy duty or hi-performance suspension....
1970-81 Camaro, Firebird, 1970-79 Nova, GM X-Body; Rear Spring Shackle Bushing Set; 8 Piece Set
This reproduction rear spring shackle bushing set is designed for 1967-1969 GM models and manufactured in high quality EPDM hard rubber to replicate the factory originals in both fit and performance. These bushings restore...
1967-69 Camaro, Firebird; 1968-81 Nova, GM X-Body; Leaf Spring Liner Set ; 5 Leaf; 8 Piece Set
These leaf spring liners promote smooth, friction free operation once installed, reducing metal to metal contact between the spring leaves. This helps quiet the ride, improve overall driving comfort, and extend the life of...
Spindle Nut & Cotter Pin; 3/4"-20 With 1-1/16" Hex Head
3/4"-20 With 1-1/16" hex head spindle nut and plated 1/8" x 1-1/2" cotter pin for securing drum or rotor to spindle. Kit contains one nut and one cotter pin. 2 kits required per vehicle. {fitment}
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
1967-80 Camaro, Nova, Firebird; Rear Leaf Spring Front Bushing; Various Models; OER
Reproduction rear leaf spring bushing for various 1967-80 GM passenger car models. A critical yet often overlooked component when restoring rear suspension performance, this bushing installs into the forward eye of the rear...
1967-69 Camaro, Firebird, 1968-79 Nova, GM X-Body; Rear Mono-Leaf Spring Installation Kit
Complete rear leaf spring installation kit engineered for 1967-1979 GM vehicles originally equipped with mono-leaf rear springs. This all-in-one solution includes correctly detailed shackles, high quality hardware, spring...
1968-79 Camaro, Firebird, Nova; Leaf Spring & Shock Anchor Plate; w/Sway Bar; Drivers Side
Reproduction of the original rear spring and shock anchor plate mount designed for use with 1968-69 Camaro and Firebird, and 1968-79 Chevy II Nova, and GM X-body models as listed below. For use on vehicles with multi-leaf...
1970-87 Buick, Chevrolet, Olds, Pontiac; Upper Control Arm Bumper; Various Models; Each
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. This upper control arm bumper is designed to replicate the factory original and is essential for proper suspension travel and ride control....
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...
1968-79 Camaro, Firebird, Nova; Leaf Spring & Shock Anchor Plate; w/Sway Bar; Passenger Side
Reproduction of the original rear spring and shock anchor plate mount designed for use with 1968-69 Camaro and Firebird, and 1968-79 Chevy II Nova, and GM X-body models as listed below. For use on vehicles with multi-leaf...