1977-96 Buick, Chevy, Pontiac Oldsmobile; Lower Control Arm; RH Passenger Side; Various Models
Replacement lower control arm for a wide variety of GM applications including 1977-96 Impala/Caprice, and various other GM full size models. Each factory replacement lower control arm includes pre-installed bushings and ball...
1977-96 Buick, Chevy, Pontiac Oldsmobile; Lower Control Arm; LH Drivers Side; Various Models
Replacement lower control arm for a wide variety of GM applications including 1977-96 Impala/Caprice, and various other GM full size models. Each factory replacement lower control arm includes pre-installed bushings and ball...
Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for various GM models. This spacer is manufactured from durable EPDM rubber. This spacer was used to correct the ride height on vehicles that did not sit level...
1970-2005 GM Cars, Trucks; Upper Ball Joint with Hardware; Various Models
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1971-2005 GM; Lower Control Arm Bushing; Passenger Car and Truck; Varius Models; Each
Reproduction control arm bushing for the lower control arm on various 1971-05 GM and various other models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning or...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
Includes all the components to replace the original bushings and hardware. Each set includes 4 bushings, 1 bolt, 1 nut, 4 washers, and 1 spacer. Set does only 1 side. 2 required per vehicle. Has 2" Spacer {fitment}
1964-1981 Various GM Vehicles Camaro, Firebird, GTO, Cutlass; Coil Spring; Spacer 3/8"
We now have reproduction of the coil spring spacer that goes between the front lower control arm and spring for 1964-81 GM Applications including Camaro, Firebird Cutlass and GTO models. It is perfect to lift the front end a...
1960-88 Various GM Vehicles Camaro, Impala, Cutlass; Front Sway/Stabilizer Bar; Bushing 1-1/4"
New 1-1/4" sway bar bushing for use with original bracket various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment. Replace the old...
Reproduction sway bar end link for various 1955-2005 GM car and truck models. Replaces the sway bar end links to eliminate issues associated with worn out links. Each sway bar link includes rubber bushings. Includes 4...
Reproduction molded rubber front coil spring insulator that mounts between the coil spring and the frame on various 1949-96 vehicles. This insulator keeps the spring from riding metal-to-metal on the frame. Coil spring...
1970-05 GM Cars / Trucks; Lower Ball Joint (Standard Size); Thread: 9/16"
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1977-79; Chevrolet Impala; Front End Rebuild Kit
1977-79 Chevrolet Impala nearly everything you need to fully rebuild a worn out front end. The kit includes a comprehensive assortment of front end parts designed to renew worn out original front suspension components. Each...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
1971-96 GM; Upper Control Arm Bushing; Various Models; Pair
Reproduction style upper control arm bushing designed for various 1971-96 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1970-96 GM Lower Control Arm Bumper, Each, Various Models
OER® reproduction of the original lower control arm rubber bumper designed for use on many GM models including the vehicles listed below. Each control arm bumper is anufactured from durable rubber with the correct...
1974-78 Mustang II 3/4" Front Sway Bar; Measures 43-1/4" Wide; For Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks running standard width crossmember Mustang II front suspension. Designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved...
1977-96 GM; Upper Control Arm; With Shaft; RH
Replacement upper control arm for a wide variety of GM applications including 1977-96 Impala/Caprice, and various other GM full size models. Each factory replacement upper control arm includes pre-installed bushings and ball...
1973-91 Buick, Chevy, GMC, Olds, Pontiac; Sway Bar Bracket; Each; Various Models
OER® reproduction of the original style "U" shaped sway bar bushing clamp designed for use with various GM models. This bracket is manufactured from stamped steel and used to hold the inner sway bar bushings and the sway...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
1970-05 GM Cars / Trucks; Lower Ball Joint (.0025 Oversize)
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
Sway Bar Bracket Set; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH and RH
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4? to 4? inclusive. These heat treated washers are for general purpose and structural use. For use...
1961-1994 GM, Ford; Upper Control Arm Bushing; Front or Rear; Various Applications
Reproduction of the original control arm bushing designed for use on the the upper control arm for various 1961-1994 GM and Ford models. Manufactured in steel clad rubber that replicates the original control arm bushing in...
1971-2005 GM; Rear Lower Control Arm Bushing; Each; Various Models
Reproduction control arm bushing for the lower control arm on various 1971-2005 GM models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning or going over...
1969-83 GM; Front Sway Bar Bushing; 1" Inner Diameter; Each
Reproduction front sway bar bushing for various GM models. This rubber bushing includes a 1" diameter hole and is installed on the the front sway bar on most models that included a heavy duty or hi-performance suspension....
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
1970-87 Buick, Chevrolet, Olds, Pontiac; Upper Control Arm Bumper; Various Models; Each
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. This upper control arm bumper is designed to replicate the factory original and is essential for proper suspension travel and ride control....
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...