1977-96 Buick, Chevy, Pontiac Oldsmobile; Lower Control Arm; RH Passenger Side; Various Models
Replacement lower control arm for a wide variety of GM applications including 1977-96 Impala/Caprice, and various other GM full size models. Each factory replacement lower control arm includes pre-installed bushings and ball...
1977-96 Buick, Chevy, Pontiac Oldsmobile; Lower Control Arm; LH Drivers Side; Various Models
Replacement lower control arm for a wide variety of GM applications including 1977-96 Impala/Caprice, and various other GM full size models. Each factory replacement lower control arm includes pre-installed bushings and ball...
1955-81 GM; Leaf Spring U-Bolts; 3-1/4" wide x 6-3/4" long; Fits 3-1/4" Axle Tubes; Pair
Replacement OE style U bolts and nuts for rear leaf springs from OER. Designed to secure the leaf spring pack to the rear axle with factory correct strength and reliability. Each set includes heat treated Grade 8 nuts and...
1970-81 Rear Spring Shackle Bushing ; Camaro, Firebird, Nova, X-Body
Replace your cracked or worn out original rear spring shackle bushings and bring your rear suspension back to original factory ride specifications. Each bushing is designed and manufactured to replicate the original in...
1967-69 Camaro, Firebird, 1968-79 Nova; Mono Rear Leaf Springs; Pair; Made in the USA!
Reproduction of the original mono rear leaf springs designed for use with 1967-69 Camaro, Firebird models, and 1968-79 Chevy II, Nova, and X-body models. Each leaf spring is manufactured to factory specifications and...
Replace the sagging leaf springs on your classic GM vehicle with this high quality set produced by OER. These replacement rear leaf springs are engineered to directly replace the original multi leaf spring set while...
1959-81 GM; Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for use on various GM models. Manufactured from durable EPDM rubber, this spacer was originally installed to correct uneven ride height on vehicles that did not...
1970-2005 GM Cars, Trucks; Upper Ball Joint with Hardware; Various Models
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
Reproduction rear leaf spring shackle for 1970-79 Chevy II/Nova, GM X-Body, and 1970-81 Camaro, Firebird models. Each shackle eplaces the old or worn out original hardware and bushings with a quality reproduction. Includes...
1975-79 X-body Nova; Front End Rebuild Kit; With Inner and Outer Tie Rod Ends
Comprehensive assortment of front end parts designed to renew worn out original front suspension components. Each component is manufactured by the original GM supplier or equivalent. Be sure you install what the factory...
1975-79 Chevrolet Camaro; Front End Suspension Rebuild Kit; with Outer Tie Rod Ends Only
Nearly everything you need to fully rebuild a worn out front end. This complete kit includes a comprehensive assortment of components engineered to renew deteriorated original front suspension parts, restoring smooth ride...
Reproduction lower control arm bushings for 1955-64 Chevrolet Bel Air, Impala, Corvair, and Full Size models. Each bushing is manufactured to factory specifications. Add new life to your suspension by replacing the old...
1970-81 Camaro, Firebird; Tubular Lower Control Arm Set; Pair
Enhance the handling performance of your 1970-81 Camaro or Firebird with these quality tubular control arms. These arms are not only stronger and lighter weight than the factory arm, they also feature improved suspension...
1975-79 Nova, Ventura, Omega, Apollo; Front End Suspension Rebuild Kit; with Outer Tie Rod Ends Only
This set includes a comprehensive assortment of front end components engineered to renew worn out suspension parts. Designed to restore proper handling, improve steering response, and reduce uneven front tire wear, this front...
1971-2005 GM; Lower Control Arm Bushing; Passenger Car and Truck; Varius Models; Each
Reproduction control arm bushing for the lower control arm on various 1971-05 GM and various other models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning or...
1968-69 Camaro, Firebird, 1968-79 Nova, X Body; Lower Rear Shock Mount Bolt; Each
Reproduction of the lower rear shock mounting bolt for 1968-1969 Camaro and Firebird models, as well as 1968-1979 Nova, 1971-1977 Ventura, 1973-1980 Omega, 1973-1975 Apollo, and 1975-1980 Skylark models equipped with multi...
Replacement sway bar designed to reduce body roll, under steer, and over steer during cornering, resulting in improved vehicle handling, control, and driving confidence. Engineered to enhance stability without negatively...
1967-81 Camaro, Firebird; Rear Shock Extension; Fine Thread; Pair
OER rear shock extenders for 1967-1981 Camaro and Firebird models. These extenders increase rear shock length by 2" and are specifically designed for use when converting from mono leaf springs to multi leaf springs. By...
Front sway bar for various 1964-1981 Buick, Chevrolet, Pontiac, and Oldsmobile models equipped with a 1-1/8" diameter bar. This versatile sway bar fits a wide range of GM vehicles including Buick Skylark and Special,...
1973-91 Chevrolet, GMC 3/4, 1 Ton 2WD Truck; Lower Control Arm; LH Driver Side
Reproduction of the original lower control arm designed for use with 1973-1991 Chevrolet and GMC truck models with 3/4 ton or 1 ton suspension. This control arm is manufactured in stamped steel to correct factory...
1970-81 Camaro, Firebird; Front Sway Bar; with WS6 Suspension; 1-1/4"
Reproduction of the original factory style 1-1/4" front sway bar designed for use with 1970-81 Camaro and Firebird models with WS6 suspension. This silver zinc plated sway bar is compatible with factory mounting brackets....
Front sway bar for various 1964-1981 Buick, Chevrolet, Pontiac, and Oldsmobile models equipped with a 1-1/4" diameter bar. Engineered to significantly reduce body roll, under steer, and over steer during cornering, this...
1970-81 Camaro, Firebird; Front Sway Bar; 1-1/16"; High Performance; LS5, LS6
Reproduction of the original factory style 1-1/16" front sway bar designed for use with 1970-81 Camaro and Firebird models including various 1964-72 Chevrolet, Buick, Olds, and Pontiac models with high performance suspension...
1973-86 Chevrolet, GMC Pickup; Upper Control Arm; 1/2 Ton; Passengers Side
Reproduction upper control arm for 1973-1986 Chevrolet and GMC truck models with 1/2 ton suspension. This control arm is manufactured in stamped steel to correct factory specifications replicating the original in quality,...
1973-86 Chevrolet, GMC Truck; Upper Control Arm; 1/2 Ton; LH Driver Side
Reproduction upper control arm for 1973-1986 Chevrolet and GMC truck models with 1/2 ton suspension. This control arm is manufactured in stamped steel to correct factory specifications replicating the original in quality,...
1968-81 Camaro, Firebird, Nova; Rear Sway Bar Anchor Plate Bolt; 7/16"-20 X 1-5/16"
Bolt and nut used to attach the rear sway bar bracket to the lower anchor plate and leaf spring perch. This case hardened bolt measures 7/16"-20 x 1-5/16" and is designed for models equipped with standard suspension. 4 bolts...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1973-91 Chevrolet/GMC C20/C30 Truck; Upper Control Arm; 3/4, 1 ton; 2 WD; LH Driver Side
Reproduction of the original upper control arm designed for use with 1973-1991 Chevrolet and GMC truck models with 3/4 ton or 1 ton suspension. This control arm is manufactured in stamped steel to correct factory...
1963-96 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Lower Control Arm Shaft Kit; 2 Wheel Drive
Reproduction control arm shaft kit, precision engineered and rigorously tested to provide a dependable replacement for the original equipment shaft. Designed as a direct fit component, this shaft installs and functions...
1958-64 Impala, Bel Air, Biscayne, 1965-82 Corvette; Lower Control Arm Shaft; LH or RH; Each
Quality reproduction lower control arm cross-shaft for various 1958-1964 Chevrolet Impala, Bel Air, Biscayne, and 1963-1982 Corvette models. Each shaft is manufactured from high quality stamped steel and built to original...
1970-81 Rear Sway Bar Bracket ; 1970-81 F-Body, 1970-79 X-Body ; Various Models
This OER® reproduction of the original rear sway bar bracket manufactured from high grade stamped steel to original specifications. Sway bar brackets hold the sway bar bushings to the frame and secures the rear sway bar...
1971-95 Chevrolet, GMC Truck; Lower Ball Joint; 2 Wheel Drive
Reproduction of the original lower ball joint designed for use on various 1971-95 Chevrolet and GMC truck models. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about...
1958-64 Impala, Bel Air, Biscayne, El Camino; Lower Control Arm Plate Set; with Screws and Washers
Reproduction of the original lower control arm plate for use with 1958-64 Chevrolet Impala, Bel Air, and Biscayne models. Each set includes a forged lower control arm plate with Grade-8 screws and washers. 2 sets required per...
1973-95 Chevrolet, GMC Truck; Upper Ball Joint; 2 Wheel Drive; RH or LH; Each
Reproduction of the original upper ball joint designed for use with various 1973-95 Chevrolet and GMC 2-wheel drive truck models. This ball joint installs into the upper control arm with bolts, washers and nuts that are...
1970-93 GM, Ford, Mopar Truck; Heavy Duty Upper Ball Joint; LH or RH; Each
Replacement upper ball joint for a wide variety of GM, Ford, Dodge, and Plymouth trucks. Each unit comes with an axially assembled retaining ring and nut, and must be pressed into the upper control arm for proper...
Reproduction control arm shaft kit, precision engineered and rigorously tested to deliver a dependable replacement for the original equipment shaft. Designed as a direct replacement, this component fits and functions exactly...
1971-99 Chevrolet/GMC; 2 WD Truck; Upper Ball Joint; with 5/8" Threads
Reproduction upper ball joint for various 1971-99 Chevrolet and GMC 2-wheel drive truck models. This ball joint installs into the upper control arm with bolts, washers and nuts that are included. Also included are the main...
1970-81 Camaro, Firebird; Rear Leaf Spring Pad Set; 4 Piece Set
Each pad is used to insulate the contact area between the leaf spring and the mounting plate, preventing metal to metal contact that can cause noise, vibration, and premature wear. These pads help maintain proper suspension...
1971-96 Chevy, GMC Pickup, Suburban, Van; Lower Ball Joint; 2 Wheel Drive
Reproduction of the original lower ball joint designed for use on various 1971-96 Chevrolet and GMC truck models. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about...
1968-69 Camaro, Firebird, 1968-79 Nova; Multi Leaf Spring Pad Set; 4 Piece Set
Each pad is designed to insulate the contact area between the leaf spring and the mounting plate, preventing metal to metal contact that can lead to noise, vibration, and premature wear. These pads help maintain proper...
1962-87 Buick, Chevrolet, Pontiac, Olds; Ball Joint Rivet Bolt Set; 24 Piece Set; Various Models
This rivet style bolt set attaches the ball joint to the upper control arm while providing the authentic appearance of factory installed rivets. Each bolt features a serrated locking rivet style head that prevents spinning...
1971-95 Chevrolet/GMC 2 Wheel Drive Truck.003 Oversize Lower Ball Joint
If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about rebuilding your front suspension. This.003 oversize ball joint is designed to be pressed into place in the lower...
Reproduction front sway bar bushing and mounting bracket set for 1964-88 Chevrolet, Buick, Oldsmobile, and Pontiac models equipped with a 1-1/4" sway bar. Manufactured to factory specifications, this set includes two...
1969-82 Rear Stabilizer Bar Link; Upper Bracket GM#485336
Reproduction rear stabilizer/swaybar bar link upper bracket for 1969-81 Chevrolet Camaro, Pontiac Firebird and 1969-1970 Chevrolet Nova models. This is the upper bracket that mounts the rear stabilizer/sway bar link to the...
Includes all the components needed to replace the original bushings and hardware. One set services only one side of the vehicle, with two sets required per vehicle. Features a 2" spacer for proper installation and alignment....
1967-81 Camaro, Firebird, Nova, GM X-Body; Rear Spring Eye Bracket Bolt Set; 6 Piece Set
Quality reproduction rear spring eye bracket bolts designed to mount the leaf spring front eye bracket. Each bolt is case hardened for exceptional durability, strength, and long lasting performance. An ideal replacement for...
1964-1981 Various GM Vehicles Camaro, Firebird, GTO, Cutlass; Coil Spring; Spacer 3/8"
We now have reproduction of the coil spring spacer that goes between the front lower control arm and spring for 1964-81 GM Applications including Camaro, Firebird Cutlass and GTO models. It is perfect to lift the front end a...
1958-88 Various GM Vehicles Chevelle, Skylark, Cutlass, GTO; Front Sway Bar; Heavy Duty Bracket; WS6
New reproduction of the OEM 1964-88 GM heavy duty front sway bar bracket for multiple GM vehicles including Chevrolet Chevelle, Buick Skylark, Oldsmobile Cutlass and Pontiac GTO models. See vehicle fitment fort all...
New reproduction of the OEM 1958-88 GM heavy duty front sway bar/stabilizer bar bushing WS6 for multiple GM vehicles including Chevrolet Chevelle, Buick Skylark, Oldsmobile Cutlass and Pontiac GTO models with 7/8" diameter...
1960-88 Various GM Vehicles Camaro, Impala, Cutlass; Front Sway/Stabilizer Bar; Bushing 1-1/4"
New 1-1/4" sway bar bushing for use with original bracket various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment. Replace the old...
1960-96 Various GM Vehicles Camaro, Cutlass, Impala; Front Sway/Stabilizer Bar; Bushing WS6; 13/16"
New 13/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
New 15/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
Reproduction sway bar end link for various 1955-2005 GM car and truck models. Replaces the sway bar end links to eliminate issues associated with worn out links. Each sway bar link includes rubber bushings. Includes 4...
1967-81 Camaro Z/28, Firebird, Nova; Rear Leaf Springs; 4 Leaf; Spring Rate 126 lbs; Pair
Reproduction of the original 4 leaf rear leaf springs designed for use with 1967-1969 Camaro Z28 (302), 1968-1981 Firebird 400 and other performance models, as well as Chevy II, Nova, and various GM X body models originally...
1971-87 Chevrolet & GMC C10/C15 Truck; Tubular Lower Control Arms; Pair
Replacement tubular lower control arms designed for 1971-87 Chevrolet and GMC 1/2 Ton C10/C15 pickup, panel, and Suburban models. Includes both RH and LH lower control arms with cross shafts, bushings, and ball joints...
Reproduction molded rubber front coil spring insulator designed to mount between the coil spring and the frame on various 1949-2002 vehicles. This insulator prevents metal to metal contact, reducing noise, vibration, and...
Bolt and nut designed to attach the rear sway bar bracket to the lower anchor plate and leaf spring perch. This case hardened fastener measures 7/16"-20 x 1-15/16" and is engineered specifically for models equipped with the...
1973-87 Chevrolet C10; Tubular Control Arm Set; Air Ride Type; Upper and Lower
Gain 21st century handling in your classic Chevy C10 truck. This is an upper and lower front tubular control arm set for conversion to air bag setup. Each set includes upper and lower tubular control arms set up for use with...
1975-81 Chevrolet Camaro; Front End Rebuild Kit; with Inner & Outer Tie Rods
Nearly everything you need to fully rebuild a worn out front end. The kit includes a comprehensive assortment of front end parts designed to renew worn out original front suspension components. Be sure you install what the...
1977-79 Impala, Caprice; Front End Suspension Rebuild Kit
1977-79 Chevrolet Impala front end rebuild kit offering nearly everything required to restore a worn out or aging suspension system. This comprehensive assortment of components is engineered to replace deteriorated factory...