Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1968-72 Outer Door Mirror; Chrome: LH; Smooth Style Base; Various GM Models
Reproduction of the original outer door mirror designed for use on various 1968-72 GM models. Each mirror is manufactured in quality die-cast zinc replicating the original mirror in quality and fit. This reproduction mirror...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
OER® reproduction of the original style 18" Trico windshield wiper blades designed to fit 3/16" side-lock connector arms. This blade is an exact reproduction for various GM models including 1970-81 Camaro, Firebird,...
1973-77 Regal; Cutlass; Monte Carlo; El Camino; LeMans; Body Mount Bushing Set; 28 piece
Reproduction 28 piece body mount bushing set for various 1973-77 GM models. Manufactured to factory specifications for proper fitment and function. These kits are made out of compression molded S.B.R. with steel sleeve...
1973-77 Chevrolet Malibu, Chevelle, El Camino; Fender Liner; Plastic; Pair
Replacement inner fender liner skirts for 1973-77 Chevrolet Malibu, El Camino and 1973-74 Chevelle models. These are the liners that mount in the front fender well. Replace the cracked, missing or warped fender liners today....
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Reproduction windshield glass for various 1973-77 GM A-Body 4-door sedan and station wagon models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against road...
OER reproduction of the front windshield glass for use with 1973-77 GM A-Body 2-door coupe models without the built-in antenna. This windshield is manufactured with tempered laminate safety glass that meets the standard for...
Wiper Blade Insert; Replacement; 16" Anco Style; Each
OER reproduction Anco-style windshield wiper blade insert for various classic American vehicle models from the 1960's and up. These 16" wiper blades are manufactured from quality molded rubber as original. Refill is...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
Reproduction of the original wiper blade units designed for use on 1970-1981 Camaro models with recessed style wipers and a wide variety of other makes and models. Manufactured in the correct design featuring the blade and...
1973-77 Chevelle, Malibu, El Camino, Laguna; Monte Carlo, Regal; Upper Door Hinge; LH Driver Side
Reproduction upper front door hinge designed for 1973-1977 GM A-Body models, including Chevrolet Chevelle, Malibu, El Camino, Monte Carlo, and Laguna. This high-quality reproduction is built to factory specifications to...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
1976-88 Buick, Chevy, Pontiac Olds; Exterior Door Handle; Black; LH Driver Side; Various Models
Reproduction of the original style exterior door handle designed for use with various 1976-88 Buick, Chevrolet, Pontiac, and Oldsmobile models. This door handle is produced in die-cast metal featuring a glossy black finish...
Original style replacement outer door mirror for 1968-72 models, features convex glass. The convex glass helps eliminate the passenger side blind spot. Each rear view mirror features the correct ribbed base and comes with a...
1973-77 Chevrolet Malibu, Monte Carlo, Olds Cutlass; Hood Hinge; LH Driver Side
Replacement hood hinge for various 1973-77 GM applications including Malibu, Monte Carlo and Cutlass. Replace the old or damaged with this brand new quality Replacement. Does not include the hood hinge spring. LH - driver...
1976-77 Chevrolet Malibu, El Camino, Laguna; Front Bumper Fillers; 2nd Design
1976-1977 Chevrolet Malibu 2dr, 4dr, wagon, Laguna, and El Camino reproduction front bumper filler panels. These filler panels fill the gap between the fender and the bumper. They are made out of rubber like the originals....
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Reproduction lower front door hinge designed for use with 1973-1977 Chevrolet Chevelle, Malibu, El Camino, Monte Carlo, Laguna, and other GM A-Body models. Each hinge is precision manufactured to factory specifications for...
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
Correct reproduction washer pump for various 1973-1984 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models. Each pump is engineered to match original equipment washer pump in functionality, fitment, and cosmetic...
Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
Reproduction of the original hood latch assembly designed for use with various GM models equipped with the release mechanism located inside the passenger compartment of the vehicle. Each hood latch is designed and...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
1968-81 GM; Trunk Storage Sleeve, Wheel Jack and Wrench, 16-3/4" x 2-1/4"; Standard Size
Correct reproduction of the original storage sleeve for the trunk wheel jack and wrench unit. This special storage sleeve was found originally on many GM car models. Manufactured from quality rubber material, this sleeve...
1976-88 Buick, Chevy, Pontiac, Olds; Outer Door Handle; Chrome; Front or Rear; LH; Various Models
Reproduction of the original style front or rear outer door handle designed for use with various 1976-88 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each handle is manufactured to correct factory...
1961-87 Buick, Chevrolet, Pontiac, Olds; Door Lock Set; with Generic Logo Keys; Bright Finish
Reproduction door lock cylinders for various 1961-87 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models as listed. Includes two door lock cylinders with bright finish face finish, two generic logo keys, cylinder...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
Replacement bullet mirror glass designed for various 1974-88 GM models equipped with bullet style exterior side view sport mirrors. This high-quality replacement allows you to restore mirror visibility without replacing the...
U-Nut Set; M6 - 1.0; Panel Range.030" to.160"; Black Phosphate; 25 Piece Set
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160"). Set of 25 u-nuts. Specifications: OE #: 11503957 Quantity:...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
Installation hardware set for various 1985-92 Camaro models including IROC-Z models. Each set includes 18 of reproduction # 11508023 bolt. Specifications: Quantity: Set of 18 Class: 9.8 Color: Black Phosphate Material: Steel...
Tapping Screw; Hex Washer Head; #8-18 x 1/2" Long; Black Oxide
Hex, washer head #8-18 x 1/2 tapping screw, in phosphate and oil coating for various applications including mounting grill to various classic vehicles Screw Specs: Description : Tapping Screw Screw Size : #8 Length : 1/2"...
Reproduction exterior mirror mounting gasket for various 1971-79 GM models with standard chrome mirrors. Each gasket is manufactured to factory specifications. Fits LH or RH side of the vehicle. {fitment}
1973-84 GM; Windshield Washer Pump Plastic Cover; Second Design
Correct reproduction windshield washer pump plastic cover for 1973-84 GM models. This is a new 2nd design wiper pump cover for many classic GM vehicles with recessed wipers and wiper motor with external terminal board. This...
Hex Bolt; 1/2"-13 x 4" LG; Gd 8; Yellow Dichromate
Hex Bolt; 1/2"-13 x 4" Lg; Gd 8; Yellow Dichromate Application 1973-1980 Chevrolet/GMC Radiator Core Support; STD Cab 1/2 & 3/4 Ton 1973-1980 Chevrolet/GMC Radiator Core Support; Crew Cab 3/4 Ton 1973-1980 Chevrolet/GMC Front...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
Bolt, 1/4-20 x 1-3/16" Dog Point Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 x 1" Pointed Tip With Hex Washer Head, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 X 7/8" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...