1970-81 Rear Spring Shackle Bushing ; Camaro, Firebird, Nova, X-Body
Replace your cracked or worn out original rear spring shackle bushings and bring your rear suspension back to original factory ride specifications. Each bushing is designed and manufactured to replicate the original in...
1967-69 Camaro, Firebird, 1968-79 Nova; Mono Rear Leaf Springs; Pair; Made in the USA!
Reproduction of the original mono rear leaf springs designed for use with 1967-69 Camaro, Firebird models, and 1968-79 Chevy II, Nova, and X-body models. Each leaf spring is manufactured to factory specifications and...
5 Leaf Rear Leaf Springs (Spring Rate 143 Lbs) - Replacement Style
Replace the sagging leaf springs on your classic GM vehicle with this quality set produced by OER! These replacement rear leaf springs are designed to replace the original multi-leaf spring set while featuring a precise...
Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for various GM models. This spacer is manufactured from durable EPDM rubber. This spacer was used to correct the ride height on vehicles that did not sit level...
1970-2005 GM Cars, Trucks; Upper Ball Joint with Hardware; Various Models
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1970-81 Camaro, Firebird, 1970-79 Chevy II, Nova and X-Body; Rear Spring Shackle Bushing Set
Reproduction rear leaf spring shackle for 1970-79 Chevy II/Nova, GM X-Body, and 1970-81 Camaro, Firebird models. Each shackle eplaces the old or worn out original hardware and bushings with a quality reproduction. Includes...
1975-79 X-body Nova; Front End Rebuild Kit; With Inner and Outer Tie Rod Ends
Comprehensive assortment of front end parts designed to renew worn out original front suspension components. Each component is manufactured by the original GM supplier or equivalent. Be sure you install what the factory...
1975-79 X-body Nova; Front End Rebuild Kit; With Outer Tie Rod Ends Only
This set includes a comprehensive assortment of front end parts designed to renew worn out front suspension components. Restore your handling and reduce front tire wear. This is an essential set when upgrading your...
1971-2005 GM; Lower Control Arm Bushing; Passenger Car and Truck; Varius Models; Each
Reproduction control arm bushing for the lower control arm on various 1971-05 GM and various other models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning or...
1968-69 Camaro, Firebird, 1968-79 Nova, X Body; Lower Rear Shock Mount Bolt; Each
Reproduction of the lower rear shock mounting bolt for 1968-69 Camaro, Firebird, and 1968-79 Nova, 1971-77 Ventura, 1973-80 Omega, 1973-75 Apollo, 1975-80 Skylark models with multi-leaf springs. This essential bolt was...
Front sway bar for various 1964-81 Buick, Chevrolet, Pontiac, and Oldsmobile models with a 1-1/8" diameter bar. This sway bar is designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved...
1970-81 Camaro, Firebird; Front Sway Bar; with WS6 Suspension; 1-1/4"
Reproduction of the original factory style 1-1/4" front sway bar designed for use with 1970-81 Camaro and Firebird models with WS6 suspension. This silver zinc plated sway bar is compatible with factory mounting brackets....
1970-81 Camaro, Firebird; Front Sway Bar; 1-1/16"; High Performance; LS5, LS6
Reproduction of the original factory style 1-1/16" front sway bar designed for use with 1970-81 Camaro and Firebird models including various 1964-72 Chevrolet, Buick, Olds, and Pontiac models with high performance suspension...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1968-81 Rear Sway Bar/Anchor Plate Bolt - 7/16"-20 X 1-5/16"
Bolt and nut used to attach the rear sway bar bracket to the lower anchor plate and leaf spring perch. This case hardened bolt measures 7/16"-20 x 1-5/16" and is designed for models equipped with standard suspension. 4 bolts...
1970-81 Rear Sway Bar Bracket ; 1970-81 F-Body, 1970-79 X-Body ; Various Models
This OER® reproduction of the original rear sway bar bracket manufactured from high grade stamped steel to original specifications. Sway bar brackets hold the sway bar bushings to the frame and secures the rear sway bar...
1962-87 Buick, Chevrolet Pontiac, Olds; Ball Joint Rivet Bolt Set; 24 Piece Set
This rivet-style bolt set attaches the ball joint to the upper control arm, providing the appearance of a real rivet. A serrated locking rivet head prevents spinning when the nut is tightened. Includes eight Grade 8 rivet...
1968-69 Camaro / Firebird, 1968-79 Nova Multi Leaf Spring Pad Set
Each pad is used to insulate the area between the spring and the mounting plate. Two upper pads and two lower pads are required on vehicles with leaf springs. {fitment} Note: When converting 1967-69 single to multi leaf a...
Includes all the components to replace the original bushings and hardware. Each set includes 4 bushings, 1 bolt, 1 nut, 4 washers, and 1 spacer. Set does only 1 side. 2 required per vehicle. Has 2" Spacer {fitment}
1964-1981 Various GM Vehicles Camaro, Firebird, GTO, Cutlass; Coil Spring; Spacer 3/8"
We now have reproduction of the coil spring spacer that goes between the front lower control arm and spring for 1964-81 GM Applications including Camaro, Firebird Cutlass and GTO models. It is perfect to lift the front end a...
1967-81 Rear Spring Eye Bracket Bolt Set (6 piece)
Quality reproduction of the original rear spring eye bracket bolt designed to mount the leaf spring front eye bracket. Each bolt is case hardened for durability and long lasting performance. 6 bolts included in each set....
1960-88 Various GM Vehicles Camaro, Impala, Cutlass; Front Sway/Stabilizer Bar; Bushing 1-1/4"
New 1-1/4" sway bar bushing for use with original bracket various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment. Replace the old...
1960-96 Various GM Vehicles Camaro, Cutlass, Impala; Front Sway/Stabilizer Bar; Bushing WS6; 13/16"
New 13/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
New 15/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
Reproduction sway bar end link for various 1955-2005 GM car and truck models. Replaces the sway bar end links to eliminate issues associated with worn out links. Each sway bar link includes rubber bushings. Includes 4...
1967-69 Camaro Z/28, Firebird 400, Nova; Rear Leaf Springs; 4 Leaf; Spring Rate 126 lbs; Pair
Reproduction of the original 4 leaf rear leaf springs designed for use with 1967-69 Camaro Z28 (302), 1968-81 Firebird 400 and performance models, Chevy II Nova and GM X-body models with 4 leaf rear springs. Each leaf spring...
Reproduction molded rubber front coil spring insulator that mounts between the coil spring and the frame on various 1949-96 vehicles. This insulator keeps the spring from riding metal-to-metal on the frame. Coil spring...
1970-81 Rear Sway Bar/Anchor Plate Bolt And Nut
Bolt and nut used to attach the rear sway bar bracket to the lower anchor plate and leaf spring perch. This case hardened bolt measures 7/16"-20 x 1-15/16" and is designed for models equipped with the Heavy Duty (F41)...
1970-05 GM Cars / Trucks; Lower Ball Joint (Standard Size); Thread: 9/16"
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
These sway bars are designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved vehicle handling and control. Offers all of the above without affecting your ride quality. Front Sway Bar...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
1971-96 GM; Upper Control Arm Bushing; Various Models; Pair
Reproduction style upper control arm bushing designed for various 1971-96 Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1970-96 GM Lower Control Arm Bumper, Each, Various Models
OER® reproduction of the original lower control arm rubber bumper designed for use on many GM models including the vehicles listed below. Each control arm bumper is anufactured from durable rubber with the correct...
1974-78 Mustang II 3/4" Front Sway Bar; Measures 43-1/4" Wide; For Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks running standard width crossmember Mustang II front suspension. Designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved...
1973-91 Buick, Chevy, GMC, Olds, Pontiac; Sway Bar Bracket; Each; Various Models
OER® reproduction of the original style "U" shaped sway bar bushing clamp designed for use with various GM models. This bracket is manufactured from stamped steel and used to hold the inner sway bar bushings and the sway...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
1970-05 GM Cars / Trucks; Lower Ball Joint (.0025 Oversize)
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1967-81 6 Piece Spring Eye Bracket Nut Kit
This is a quality OER® reproduction nut which is used to mount the leaf spring front eye bracket. Sold as a 6 piece kit. Applications: 1973-74 Buick Apollo 1975-79 Buick Skylark 1967-81 Chevrolet Cam aro 1968-79 Chevrolet...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
Sway Bar Bracket Set; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH and RH
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4? to 4? inclusive. These heat treated washers are for general purpose and structural use. For use...
Front sway bar for various 1964-81 Buick, Chevrolet, Pontiac, and Oldsmobile models with a 1-1/8" diameter bar. This sway bar fits a wide variety of models including Buick Skylark, Special, Chevrolet Chevelle El Camino,...
1967-81 Rear Spring Eye Bracket Nut
Quality OER® reproduction of the original rear spring eye bracket nut used to mount the leaf spring front eye bracket. Sold individually. 6 required per vehicle. Applications 1967-81 Camaro models 1967-81 Fir ebird models...
1968-79 Rear Leaf Spring Pad ; Multi Leaf ; Upper and Lower ; Camaro, Firebird, Nova, X Body
Reproduction of the original multi leaf, upper and lower rear leaf spring pad designed for use on various GM models. Each pad is manufactured to OE specifications in EPDM rubber compound. Always replace the rear leaf spring...
1970-81 Camaro, Firebird, 1975-79 Nova; Rear Leaf Spring Installation Set; Multi-Leaf
Reproduction of the original and complete rear leaf spring installation kit designed for use on 1970-81 various GM vehicles equipped with multi-leaf rear springs including 1970-81 Camaro, Firebird, 1975-79 GM X-body models as...
1967-81 GM; Rear Leaf Spring Front Eye Bracket Bolt ; Each
Quality reproduction of the original rear spring eye bracket bolt designed to mount the leaf spring front eye bracket. Each bolt is case hardened for durability and long lasting performance. Sold individually. {fitment}
1961-1994 GM, Ford; Upper Control Arm Bushing; Front or Rear; Various Applications
Reproduction of the original control arm bushing designed for use on the the upper control arm for various 1961-1994 GM and Ford models. Manufactured in steel clad rubber that replicates the original control arm bushing in...
1971-2005 GM; Rear Lower Control Arm Bushing; Each; Various Models
Reproduction control arm bushing for the lower control arm on various 1971-2005 GM models. Manufactured in steel clad rubber to be pressed into place. If your suspension rattles or makes noises when turning or going over...
1969-83 GM; Front Sway Bar Bushing; 1" Inner Diameter; Each
Reproduction front sway bar bushing for various GM models. This rubber bushing includes a 1" diameter hole and is installed on the the front sway bar on most models that included a heavy duty or hi-performance suspension....
1970-81 Camaro/Firebird, 1970-79 Nova / X-Body Rear Spring Shackle Bushing Set
Replace your cracked, shrunken or worn out shackle bushings and bring your rear suspension back to original factory ride specifications. Set includes 8 bushings. Note: No further discounts apply.
Spindle Nut & Cotter Pin; 3/4"-20 With 1-1/16" Hex Head
3/4"-20 With 1-1/16" hex head spindle nut and plated 1/8" x 1-1/2" cotter pin for securing drum or rotor to spindle. Kit contains one nut and one cotter pin. 2 kits required per vehicle. {fitment}
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
1967-80 Camaro, Nova, Firebird; Rear Leaf Spring Front Bushing; Various Models; OER
Reproduction rear leaf spring bushing for various 1967-80 GM passenger car models. A critical yet often overlooked component when restoring rear suspension performance, this bushing installs into the forward eye of the rear...
1967-69 Camaro, Firebird, 1968-79 Nova; Rear Leaf Spring Installation Kit; Mono Leaf
OER® offers this complete rear leaf spring installation kit designed for use on various 1967-79 GM vehicles equipped with mono-leaf rear springs including 1967-1969 Camaro and Firebird models. Each leaf spring...
1968-79 Camaro, Firebird, Nova; Leaf Spring & Shock Anchor Plate; w/Sway Bar; Drivers Side
Reproduction of the original rear spring and shock anchor plate mount designed for use with 1968-69 Camaro and Firebird, and 1968-79 Chevy II Nova, and GM X-body models as listed below. For use on vehicles with multi-leaf...
1970-87 Buick, Chevrolet, Olds, Pontiac; Upper Control Arm Bumper; Various Models; Each
Reproduction control arm bumper for Buick, Chevrolet, Oldsmobile, and Pontiac models. This upper control arm bumper is designed to replicate the factory original and is essential for proper suspension travel and ride control....
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...