OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1968-81 Trunk Lid Bumper On Lid; 7/8" Diameter, 1/2" thick
Correct replacement bumper to eliminate the lid from touching the body and causing unnecessary damage. Dimensions: Body Diameter: 7/8" Body Height: 1/2" Mounting hole diameter: 7/32" Overall Height: 13/16" {specs} {fitment}
1958-84 GM; Outer Rear Hood Rubber Stoppers; Pair; Various Models
Reproduction outer rear hood bumpers for various GM models. Each bumper is manufactured to quality EPDM rubber compound and matches the original in dimensions allowing proper fitment. Sold in pairs. Use as required Buick...
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
1961-83 GM; Rubber Bumper Stopper; 1-3/16" Long; Various Uses and Models; Each
Correct replacement of the rubber bumper for use on various GM models. This rubber stopper will help insure that your seat/hood is aligned properly. Sold individually. Use as required per vehicle. Buick Applications 1971-1972...
1955-81 Chevrolet, GMC, Pontiac; Air Cleaner Lid Rubber Seal; 59" Long x 5/16" Wide
Reproduction air cleaner lid seal for a variety of GM car and truck models as listed. Designed to seal the area between the lid and the base offering a tight seal for the air cleaner on models that required this seal. {specs}...
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1955-90 GM; Door Lock Gasket; Various Models
Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...
1961-79 GM; Bucket Seat Back Rubber Stopper Set; Round; w/Mounting Screws; Pair
Reproduction of the original seat back rubber stoppers designed for use on various 1961-79 GM models. These rubber stoppers help prevent rattling and keep the seat back positioned correctly. Replace worn out or missing seat...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1955-1976 Glove Box Door Arm Rubber Stopper
Reproduction of the original glove box door arm rubber stopper designed for use on various GM models. Eliminate the rattling and looseness of the glove box door by simply replacing the worn out or missing rubber glove box...
Sealstrip Glass Setting Tape; 10 Foot Roll; 1/32" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1970-88 Buick, Chevrolet, Oldsmobile, Pontiac; Outer Door Handle Gasket; LH or RH ; Each
Reproduction door handle gasket for 1970-81 GM F-Body and 1973-88 G-Body models. This gasket inserts on the back of the outer door handle and acts as protection between the handle and the paint. Sold individually. 2 gaskets...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
1958-75 Clutch Bellcrank Felt Seals ; Pair
OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...