1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Reproduction of the original style fuel tank designed for use with 1975-76 Impala, Bel Air, and Caprice station wagon models (except 2 and 4 door coupe models). Each fuel tank is manufactured in quality stamped steel and zinc...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Reproduction of the original style fuel tank designed for use with 1975-76 Impala, Bel Air, and Caprice models. Each fuel tank is manufactured in quality stamped steel and zinc plated matching the original OE design. Features...
1975-76 Impala / Full Size (Ex Wagon); Fuel Tank With Neck; 26 Gallon; Niterne Steel; GM40N
Replacement fuel tank for 1975-76 Chevrolet passenger models (except wagon). This fuel tank is made of niterne-coated steel and features a filler neck, measures 33 3/4" x 31 3/4" x 9 3/8", has a capacity of 26 gallons (98...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
1967-75 Various GM Applications; Quadra Jet Carburetor Base Gasket; Heat Shield
Reduces heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket fits 67-75 GTO/Firebird, 67-75 Camaro, Chevelle, El...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1974-81 Outer Accelerator Pull Spring
Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction of the original style fuel tank designed for use with 1970-74 Impala, Bel Air, Biscayne, Catalina, Bonneville and GM full size station wagon models. This fuel tank is made of zinc-coated steel and has a capacity...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Reproduction of the original gas tank straps designed for use with 1973-1978 Electra, LeSabre, Riviera, Impala, Bel Air, Caprice, Bonneville, Catalina, and other GM full size models (except station wagon). Each strap is...