1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van...
1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Reproduction of the original fuel tank mounting straps designed for use with 1974-75 Camaro, Firebird, and 1973-75 Nova and GM X-Body models. Each strap is produced using heavy duty pre-formed steel for an original...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
1967-75 Various GM Applications; Quadra Jet Carburetor Base Gasket; Heat Shield
Reduces heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket fits 67-75 GTO/Firebird, 67-75 Camaro, Chevelle, El...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1974-81 Outer Accelerator Pull Spring
Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1974-81 Camaro, Firebird; Fuel Tank Brace Set; 4 Piece Set
Reproduction of the original fuel tank braces for use with 1974-81 Camaro and Firebird models. Braces are manufactured from stamped steel to the correct OE configuration replicating the original for authenticity and fitment....
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1975-81 Camaro, Firebird; Accelerator Cable; 267, 305U, 305, 350L
Factory service replacement accelerator cable for use with 1975-81 Camaro models with 267, 305, 350 V8 engines, and 1976-80 Firebird models with 305U, 350L, 1980 267, 350H NM6 Canadian emissions (export). This cable extends...