Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1970-74; Challenger, Barracuda, Cuda; Hood Hinges; with Springs; Pair
Reproduction of the original 1974 Plymouth Cuda hood hinges designed for 1970-74 Mopar E-body models. Each hood hinge is manufactured to exact factory specifications and includes OE style hood hinge springs. Get your hood in...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1973-74 Barracuda, Cuda; Front Bumper; with Jack Slots; Chrome; OER Premier; Show Quality
OER Premier chrome front bumper for 1973-74 Plymouth Barracuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating...
1974 Barracuda, Cuda; Rear Bumper; with Jack Slots; Chrome; OER Premier; Show Quality
OER Premier chrome rear bumper for 1974 Plymouth Barracuda, Cuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
1970-76 Dodge, Plymouth, A, B, E Body; Door Lock Striker Bolt; 2 Door; Each
Correct reproduction of the original door lock striker bolt designed for use on all 1970-76 Dodge and Plymouth A, B, and E body 2 door models as listed. The door lock striker bolt is manufactured to correct factory dimensions...
1970-74 Barracuda, Cuda, Challenger; Inner Fender Apron Set; 12 Piece Set; Drivers Side
Reproduction of the original inner fender apron set designed for use with 1970-74 Barracuda, Cuda, and Challenger models. Each fender apron set is manufactured in stamped steel to original factory specifications featuring...
1970 Plymouth Barracuda, Cuda; Hood Latch Assembly; EDP Coated
Reproduction of the original hood latch assembly panel designed for use with 1970 Barracuda and Cuda models. Each hood latch assembly is manufactured in stamped steel to original factory specifications featuring correct...
1970-74 Plymouth Barracuda, Cuda; Outer Door Handle Set; with Gaskets; RH & LH; Pair
Reproduction of the original outer door handles designed for use with 1970-74 Plymouth Barracuda and Cuda models. Each door handle is manufactured in quality die-cast zinc featuring a polished chrome plating replicating the...
1971-74 Dodge, Plymouth B & E-Body; Remote Outer Door Mirror; Drivers Side
Reproduction of the original style remote "bullet" mirror designed for use with various 1971-74 Dodge and Plymouth B, E Body models. Each mirror is manufactured in quality die-cast zinc featuring a primed and ready-to-paint...
1971-74 Barracuda / "Cuda Front Door Window Regulator, RH
Reproduction of the original front door window regulator designed for use on 1971-1974 Plymouth Barracuda and Cuda models. All stamped steel construction, features correct splined shaft and correct retaining screw threads for...
1971-74 Dodge, Plymouth B/E-Body; Chrome Outer Door Mirror; Manual Bullet; Passenger Side
Reproduction of the original "bullet style" outer door mirror designed for use with various 1971-74 Dodge and Plymouth models. Each mirror is manufactured in quality die-cast zinc featuring a beautiful chrome plated surface....
1971-74 Dodge, Plymouth B/E-Body; Manual Bullet Outer Door Mirror; Paintable; Passenger Side
Reproduction of the original manual style bullet mirror designed to replace the damaged or worn out original on the passenger side door. Each mirror is designed to mount and install same as original and includes all hardware...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1970-74 Barracuda, Cuda, Challenger; Upper Door Hinge; LH; EDP Coated
Reproduction of the original upper door hinge designed for use with 1970-74 Dodge, Plymouth E-Body models. Manufactured in quality stamped steel replicating the origina l in quality and design. Includes correct mounting...
1970-74 Barracuda, Cuda, Challenger; Lower Door Hinge; RH
Reproduction lower door hinge for 1970-74 Dodge, Plymouth E-Body, Barracuda, 'Cuda, and Challenger models. Manufactured in quality stamped steel replicating the original in quality and design. Features correct mounting holes...