This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1976-81 Camaro, Firebird, 1973-79 Nova, X-Body; Fuel Tank Sending Unit; with Return Line; 3/8" Line
Reproduction fuel tank sending unit for a variety of GM models. After years of use, your fuel sending unit can wear out or stop working entirely. When that happens, it can cause your fuel gauge not to work or even send...
Reproduction of the complete accelerator pedal assembly which extends from the firewall on all V8-equipped 1967 Firebird models. This accelerator pedal assembly comes complete with the pedal, pedal mount pin and spring,...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1962-81 GM; Fuel Tank Sending Unit Lock Ring; Small; 1-15/16"; Various Models
Correct reproduction fuel tank sending unit locking ring which secures the fuel tank sending unit to the gas tank. Replaces the original ring which are commonly destroyed when being removed. This ring helps to seal the...
This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...
1969-81 Fuel and Brake Line Clip ; Dual Line 3/8" and 1/4"
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
1968-74 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Pad to Rod Support
Reproduction of the original style GM accelerator pedal rod support for use on the various Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each support is manufactured in injection molded ABS offering an exact...
Fuel and Brake Line Clip Set ; Dual Line 3/8" and 1/4" ; 7 Piece Set
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...