Electric Vacuum Pump Set For Power Brakes - Universal Fit
It takes 16" of Hg vacuum to properly activate your vehicle's power brake booster. Sometimes, big-cammed or supercharged engines don't create enough vacuum to operate the booster, making it more difficult to stop. This vacuum...
Disc/Disc Brake Combination Valve
If you need a new disc brake metering valve or want the more updated look of a brake combination valve in your 1967-72 model, or need a replacement for a 1971-77, this carefully machined reproduction brass combination valve...
1967-70 Master Cylinder Cover; Single Bail; Without Diaphragm; Chrome Plated
Reproduction 4-7/8" x 2-3/8" single bail master cylinder cover. Produced in stamped steel and finished in bright chrome plating. Includes the steel bail retainer. Rubber diaphragm sold separately. Replaces OE #'S 18000781,...
1967-81 Buick, Chevrolet, Pontiac, Oldsmobile; Brake Pad Trim Plate; with Auto Trans
Correct reproduction of the original chrome brake pad trim bezel designed for use with various GM 1967-81 F, Y, and X body models with automatic transmission brake pads. Manufactured in stampled aluminum featuring a bright...
1964-82 Buick, Chevy, Pontiac, Oldsmobile; Brake Pedal Pad; with Auto Trans; Drum Brakes
Reproduction of the original brake pedal pad for use on various 1964-82 GM models with automatic transmissions. Manufactured in quality EPDM flexible rubber that makes installation easy when appplying to the brake pedal....
1968-79 Camaro, Nova, 1970-75 Firebird; Brake Pedal Pad; with Manual Trans; OER
This correct OER® reproduction of the original brake pedal pad is designed for use on various GM models including 1968-79 Camaros equipped with both a manual trans and disc brakes. The reproduction features the correct...
Correct double push type clip for various GM models. Clip is stamped to factory dimensions for an original replacement, replacement of the rivet style clip, or can used as a universal fit part whenever clamps are needed to...
1967-87 Buick, Chevrolet, Olds, Pontiac; Brake or Clutch Pedal Pad; Each
Reproduction brake or clutch pedal pad for a variety of GM models equipped with manual transmissions and drum brakes. Manufactured in quality EPDM rubber replicating the original horizontal ribbed design. This pedal pad can...
Brake and Clutch Pedal Bushing Set; Nylon; For 5/8" Diameter Shaft; 5/8" Deep; 4-Piece Set
Reproduction of the commonly worn out nylon pedal bushings for various GM and Ford vehicles. Split nylon flange bushings fit over clutch pedal cross shaft and inside cross shaft sleeve for clutch and brake pedals with 5/8"...
If you need a new disc brake metering valve or want the more updated look of a brake combination valve, or need a replacement, then this carefully machined reproduction brass combination valve is the perfect replacement...
1969-81 Fuel and Brake Line Clip ; Dual Line 3/8" and 1/4"
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1955-81 Buick, Chevy, Pontiac, Oldsmobile; Brake Cable Clip; Each
Reproduction of the original brake cable clip designed for use with a variety of 1955-81 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each clip is manufactured in quality heat stamped steel replicating the...
Fuel and Brake Line Clip Set ; Dual Line 3/8" and 1/4" ; 7 Piece Set
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1969-80 Buick, Cadillac, Chevrolet, Oldsmobile, Pontiac; Bleeder Valve Dust Caps; Pair
Reproduction of the original blue bleeder valve dust caps designed for use with various models from 1969-1980. These dust caps are installed in seconds on your brake bleeder screws to keep road debris and the elements from...
1967-72 GM; Brake or Return Fuel Line Clip; Under Body; R-Profile; 3/16"; Each
Reproduction of the original under body brake and fuel line clip for various 1967-72 GM models. This clip secures the brake and fuel line to the under body to keep the brake and fuel lines out of harm's way. This is a 3/16"...
Spindle Nut & Cotter Pin; 3/4"-20 With 1-1/16" Hex Head
3/4"-20 With 1-1/16" hex head spindle nut and plated 1/8" x 1-1/2" cotter pin for securing drum or rotor to spindle. Kit contains one nut and one cotter pin. 2 kits required per vehicle. {fitment}
5/16-18 X 9/16" Self-Tapping Bolt. Brake and fuel line bolts with correct Anchor head marking. Self tapping, non pointed 1/2" bolt. Set of 6. {fitment}