Delco Energizer R59 Battery Topper Top Post
Now you can turn any modern style battery into a vintage looking one by adding this battery topper featuring the correct special grain just as original. Battery toppers are designed to be used with any maintenance free flat...
1955-80 GM; Bolt, Pointed Tip; with Hex Washer Head, 5/16-18 X 1-1/4"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1968-92 GM, Chrysler; Door Jamb Switch; 2 Terminal
Replacement door jamb switch for use on various 1968-92 GM models. This 2 terminal switch is manufactured to fit and function as original and specifically designed for the models listed below. Replacing this switch will help...
1969-76 GM; Turn Signal Switch; 10-Pin; 3-7/8" Wide Connector
Reproduction turn signal switch for various 1969-76 GM models. Located in the steering column, this switch features the correct color-coded wiring and proper 3-7/8" wide plastic connector for a plug-in installation. 10 wire...
1968-69 Camaro, Caprice, Corvette; Headlamp Switch; with Concealed Headlamps; 8-Pin Design
Reproduction of the original headlight switch assembly designed for use with 1968-69 Camaro Rally Sport, 1968 Caprice, and 1968-77 Corvette models with the concealed (hidden) headlamp option. Once replaced, this switch will...
Chevrolet Small Block / Big Block 1.4 HP High Torque Gear Reduction Mini Starter
Manufactured with die-cast and billet aluminum. This new high performance gear reduction starter weighs only 10 lbs.! Fits small block and big block Chevy V8 models with 153 and 168 tooth flywheels, standard or automatic...
1968-74 Chevrolet; Starter Motor Solenoid Heat Shield; with Big Block; Various Models
Reproduction of the factory-style solenoid heat shield designed for use on various 1968-74 big block Chevrolet models. This high-quality shield is manufactured in stamped steel to match the original configuration for an...
1972-76 Buick, Chevrolet, Pontiac, Oldsmobile; Windshield Wiper Switch & Knob; Varius Models
Reproduction of the original style windshield wiper switch designed for use with the various 1972-76 General Motors vehicles listed below. Each wiper switch is manufactured to replicate the original in appearance, fitment,...
Delco Energizer R89 Side Post Battery Topper
Now you can turn any modern style battery into a vintage looking one by adding this battery topper featuring correct special grain just as original. Battery toppers are designed to be used with any maintenance free flat top...
Cloth Wiring Harness Tape; 1" x 100 foot
If you want an OEM quality and appearance for your original or reproduction wiring, this specially manufactured black! This adhesive back tape will allow you to re-wrap your existing harness or replace tape which may have...
1964-79 Chevrolet; Alternator Pulley; Deep Groove; 3-3/16" Diameter
Reproduction 3-3/16" diameter deep groove alternator pulley for various 1965-1979 Chevrolet models as listed. Each pulley is manufactured from solid steel and precision machined to match the OE Design. Each pulley is Zinc...
1968-88 GM; Transmission Throttle Control Kickdown Switch; with M40 TH400 Transmission
Reproduction kickdown (downshift) switch or transmission throttle control switch for various 1968-88 Buick, Chevrolet, Pontiac, and Oldsmobile models with an M-40, TH400 transmission as listed. Each switch is manufactured to...
1969-76 Chevy; Alternator Bracket Set; with Small Block; Long Water Pump; Polished Chrome
This convenient aluminum alternator bracket set is designed for small block Chevy engines with long style water pump. Will work to mount the alternator on the RH or passenger side of the vehicle using original holes in the...
1969-86 Chevrolet Big Block; Chrome Upper Alternator Bracket; With Long Water Pump
Chrome reproduction big block upper alternator bracket with factory intake manifolds. This bracket is for use with long water pumps on models equipped with an original big block engine.
1969-74 Chevrolet Nova; Headlamp & Windshield Washer Switch Ground Strap; with Bracket
Reproduction of the original style headlamp and windshield washer switch ground strap for use with 1969-74 Chevrolet Nova reproduction headlamp and wiper switch ground strap and bracket. This reproduction is manufactured to...
1967-78 Chevrolet; Relay; Cowl Induction, Power Window, Tailgate; Various Models
Reproduction relay assembly for various 1967-78 Chevrolet models including 1969 Camaro Cowl Induction system as well as other models for electric window and power tailgates. This relay installs on the firewall for 1969 Camaro...
Top Post Battery Cable Terminal
Due to the corrosive nature of battery electrolyte, the original lead cast positive and negative terminal ends usually require replacement every few years. We offer these replacement OEM type terminals for use on top post...
OER Smart Charger 1250; Smart Battery Charger And Maintainer; 6V/12V; 1.25 Amp
The OER Smart Charger 1250 battery charger and maintainer for classic cars and trucks provides high frequency automatic intelligent charging for 6V or 12V lead-acid, flooded, or sealed maintenance-free (AGM and Gell Cell)...
1969-75 Chevrolet; Upper Alternator Bracket; Small Block; EDP Coated
This bracket is a reproduction of the upper alternator bracket GM used on 1969-75 small block Chevrolet engines with a long water pump. This bracket has the correct adjuster slot, all the mounting holes and the hole for the...
1973-80 Chevy Pickup, Blazer, Suburban Truck; Auxiliary Battery Tray Assembly; EDP Coated
Reproduction of the original auxiliary battery tray assembly designed for use with 1973-80 Chevrolet and GMC pickup, Blazer, Suburban, and Jimmy models. Manufactured in quality stamped steel to GM specifications. Features...
New reproduction ignition key buzzer switch to fit a wide variety of 1969-96 GM models without a tilt steering column. You can now replace your broken or missing buzzer switch with this new factory OEM style replacement...
1969-76 Chevrolet Corvette; Ignition Warning Switch; Key Minder Buzzer
New reproduction ignition key buzzer switch to fit a wide variety of 1969-76 Chevrolet Corvette with tilt and telescopic steering column. You can now replace your broken or missing buzzer switch with this new factory...
1971-94 Chevrolet, Oldsmobile, Pontiac; Switch; Ignition Buzzer; Key Alarm; For Models With Tilt
New reproduction ignition key buzzer switch to fit a wide variety of 1971-94 GM models with a tilt steering column. You can now replace your broken or missing buzzer switch with this new factory OEM style replacement...
Side Post Battery Cable Terminal
Due to the corrosive nature of battery electrolyte, the original lead cast positive and negative terminal ends usually require replacement every few years. We offer this replacement OEM type terminal for use on side terminal...
1964-75 Buick, Chevy, Olds, Pontiac; Alternator Cap and Retainer Set; Red
Reproduction alternator wire terminal cap and retainer for various 1964-75 Buick, Chevrolet, Oldsmobile, and Pontiac vehicles equipped with a GM threaded-post type alternator. The retainer attaches behind the alternator post...
1970-84 Chevrolet, GMC; Starter Motor Brace; For 168 Tooth Starter
Stamped steel starter motor brace for a wide variety of 1970-84 Chevrolet and GMC car and truck models with 168 tooth starter. Over a period of years, the starter motor brace can be lost or discarded when the starter is...
1969-77 GM Vehicles; Relay; For Accessory; Blower Motor, Power Antenna; 5 Terminal
Reproduction accessory relay for blower motor or power antenna on various 1969-77 GM vehicles. Each relay is produced with the bracket, as original, for a bolt-on replacement of the original. Features 5 terminals. Replaces OE...
1963-79 Buick, Cadillac, Chevrolet, GMC, Oldsmobile, Pontiac; Alternator Fan Blade; 10-Blade
Service replacement style 10-blade alternator fan to fit a wide variety of Delco alternators from the 1963-79 model era. This is an exact reproduction of the now obsolete Delco service replacement part that was sold under the...
1970-81 Camaro; Windshield Wiper Motor Ground Strap; with Recessed Wipers
Reproduction wiper motor ground strap for 1970-1981 Camaro models equipped with recessed windshield wipers. Each strap is manufactured to factory specifications for a precise fit and original appearance. Designed as a direct...
Starter Bolt 3/8"-16 X 4-11/16"
Replacement starter bolt for models that require a 3/8"-16 x 4-11/16" bolt.
1956-96 AMC, Chrysler, GM, Ford; Wiring Connector; 2-Terminal; Female; Various Applications
Reproduction 2-terminal wiring connector with pigtail to fit a wide variety of AMC and GM applications. This connector is used on relays, AC clutch cycle switches, AC compressor, back-up lamp switches, HVAC components,...
1964-81 GM Cars, Trucks; Battery Tray Clamp
Reproduction battery tray clamp for 1964-81 GM models. Manufactured in quality stamped steel to OE specifications. Designed to replace your missing or corroded original clamp while presenting an authentic factory appearance....
1966-81 GM; Spare Tire Hold Down Rod; 1970-81 Firebird; Battery Hold Down Bolt; 5/16"-18 x 9-3/4"
Reproduction spare tire hold down rod for various applications and 1970-81 Firebird battery hold down rod. Each rod is manufactured in stamped steel to factory specifications. Depending on the application, you may need to...
Front Fender Wire Harness Straps; 2-1/4" Long; Black Nylon
A hot exhaust manifold can cause serious damage to your electrical system. If not properly fastened, the wiring harness leading to your alternator/generator or other wiring harnesses could fall into an open area between the...
1958-96 GM; Horn Assemblies; with Universal Mount Brackets; Delco-Remy Markings; GM Licensed
Quality reproduction of the original horn assembly designed for use with various 1958-96 Buick, Chevrolet, Oldsmobile, and Pontiac models. Each horn is manufactured to factory specifications replicaing the original in...
OER reproduction of the original battery tray designed for use on 1970-1981 Camaro models. Manufactured in quality stamped steel to GM specifications. Will install as original and features correct mounting points. Possibly...
1973-80 Chevrolet, GMC Truck; Battery Tray Brace; C10
Reproduction of the original battery tray brace designed for use with 1973-80 Chevrolet and GMC pickup trucks, Blazer, Jimmy and Suburban models. Manufactured in stamped steel replicating the original in quality and design....
Manufactured with die-cast and billet aluminum. This new high performance gear reduction starter weighs only 10 lbs! Fits small block and big block Chevrolet V8 models with 153 and 168 tooth flywheels, standard or automatic...
1973-80 Chevrolet, GMC Pickup, Blazer, Jimmy, Suburban; Battery Tray Bottom; C10; EDP Coated
Reproduction of the original battery tray designed for use on various 1973-80 Chevrolet and GMC pickup trucks Blazer, Jimmy and Suburban models. Manufactured in quality stamped steel to GM specifications. Features correct...
1968-1974 Chevy II, Nova, Ventura, Omega, Apollo; Battery Tray; EDP Coated
Reproduction battery tray for 1968-1974 Chevy II, Nova and GM X-body models. Manufactured in quality stamped steel to GM specifications. Features correct mounting points. Possibly one of the most overlooked items in the...
1969-74 Chevrolet; Alternator Bracket Set; RH Mount; Big Block; 5-Piece Set
Reproduction alternator bracket set for 1969-74 Chevrolet big block models (396, 402, 427, 454). This set is designed as a replacement for worn, rusted, or missing originals. Manufactured in the correct gauge stamped steel,...
1973-75 Chevrolet Impala, Caprice; Battery Tray
Quality reproduction of the original battery tray designed for use on various 1973-75 Chevrolet Impala and Full Size models. Manufactured in quality stamped steel to OE specifications. Features correct mounting points....
Correct reproduction of the original neutral safety switch designed for use with various 1970-79 GM models with manual transmissions. Replace your original worn-out switch and ensure the back up lamps are in proper working...
1973-77 Chevrolet Chevelle, Monte Carlo, Malibu, El Camino; Battery Tray
Reproduction battery tray for 1973-77 Chevrolet Chevelle, Monte Carlo and El Camino models. Replace the old, rusty battery with this great reproduction. This tray meets or exceeds the OEM and features a corrosion resistant...
1966-81 GM Cars, Trucks; Battery Tray Clamp; Stainless Steel
Stainless steel reproduction of the original style battery tray clamp designed for use on various 1964-81 GM models. Manufactured in quality stainless steel to OEM specifications. Will fit and install on the applications...
1971-76 Chevrolet Impala Convertible, Wagon; Convertible Top/Tailgate Window Switch
Replacement convertible top or tailgate window switch for 1971-76 Chevrolet Impala convertible and wagon models. Manufactured correct markings matching the OEM. Three terminals and black lever. Sold individually.
1970-75 Camaro, Nova, Impala; TCS Transmission Spark Control Relay; 350, 396
Reproduction TCS relay for 1970-75 Chevrolet models equipped with a 4 speed transmission and TCS system. Each relay is manufactured replicating the original Delco design featuring the OE # 3961573 stamped into the casing....
1954-81 Buick, Chevrolet, GMC, Oldsmobile, Pontiac; Circuit Breaker; 30 Amp
Reproduction 30 amp circuit breaker for various GM applications. This circuit breaker was used in multiple systems requiring a 30 amp breaker, including power seats, power windows, power door locks, power convertible tops,...
OER Smart Charger 800; Battery Charger And Maintainer; 12V; 0.8 Amp
The OER Smart Charger 800 battery charger and maintainer for classic cars and trucks provides high frequency automatic intelligent charging for 12V lead-acid, flooded, or sealed maintenance-free (AGM and Gell Cell) batteries....
3/8"-16 X 3-5/8" Starter Mount Bolt
This replacement shouldered medium length bolt commonly used to secure starters with a cast iron staggered pattern nose to a big block engine. Two bolts required per vehicle.
1973-1997 GM; 2 Terminal Door Jamb Switch; Various Models
Replacement door jamb switch for use on various GM models with two terminals for the drivers side. This switch is a GM service replacement part, which may differ slightly from the original in appearance but will fit and...
Headlamp Switch; 3 Position; Universal Fit
Universal fit headlamp switch for a wide variety of vehicle applications from the 1940's and beyond. Each switch features 3 position push/pull functionality with knob and shaft. Required a 3/8 diameter hole for mounting, and...
1962-79 GM; Windshield Wiper Motor Ground Strap; w/o Recessed Wipers
Reproduction wiper motor ground strap for various 1962-1979 GM vehicles. Each strap is manufactured to factory specifications for proper fit and authentic appearance. Designed as a direct replacement to restore correct...
1964-75 Buick, Chevy, Olds, Pontiac; Alternator Cap and Retainer Set; Black
Reproduction alternator wire terminal cap and retainer for various 1964-75 Buick, Chevrolet, Oldsmobile, and Pontiac vehicles equipped with a GM threaded-post type alternator. The retainer attaches behind the alternator post...
1973-80 Chevy Pickup, Blazer, Suburban Truck; Main Battery Tray Assembly; EDP Coated
Reproduction of the original main battery tray assembly designed for use with 1973-80 Chevrolet and GMC pickup, Blazer, Suburban, and Jimmy models. Manufactured in quality stamped steel to GM specifications. Features correct...
1980-15 4-Terminal Make & Break Miscellaneous Relay
Reproducion 4 terminal make and break relay used for various functions such as lighting, horns on a multitude of vehicles from 1980-2015. This 4 terminal relay is also popular in the aftermarket for lights, light bars, vacuum...
1960-84; GM, Chrysler, Dodge, Plymouth; Door Jamb Switch; Single Terminal; Each
Replacement single terminal door jamb switch designed for use on various models. Replace the old, damaged or non working door jamb switch with this quality service replacement. The door jamb switch will get your interior dome...
Heater Hose Clip for Inner Fender Skirt; Various GM Applications
This hose clip is designed to secure a pair of heater hoses to the inner fender skirt to prevent damage of the hoses and keep the engine compartment neat and tidy in appearance. This heater hose clip was original equipment on...
Reproduction or service replacement lamp socket and pigtail for a wide variety of GM applications. Produced iin high quality heat resistant plastic with stamped steel contacts anodized in silver for corrosion resistance and...
OER® reproduction of the original oil pan battery cable clip designed for use on various GM models. Manufactured in stamped steel with a plastic coating that protects the cable. Installs between the oil pan bolt and the...