Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1970-74; Challenger, Barracuda, Cuda; Hood Hinges; with Springs; Pair
Reproduction of the original 1973 Plymouth Barracuda hood hinges designed for 1970-74 Mopar E-body models. Each hood hinge is manufactured to exact factory specifications and includes OE style hood hinge springs. Get your...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
1973-74 Plymouth Barracuda; Front Bumper; With Jack Slots; Chrome; OER Premier; Show Quality
OER Premier chrome front bumper for 1973-74 Plymouth Barracuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating...
1973 Plymouth Barracuda; Rear Bumper; With Jack Slots; Chrome; OER Premier; Show Quality
OER Premier chrome rear bumper for 1973 Plymouth Barracuda models. This reproduction bumper is designed exclusively for the restorer who demands the best the market has to offer. Features superior triple chrome plating that...
1970-74 Plymouth; Barracuda, Cuda; Back Window Glass; Coupe; Tinited
Reproduction of the original style back window glass designed for use with 1970-74 Plymouth Barracuda, and Cuda models. Replace your missing, scratched or broken original vent glass with this new DOT (department of...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
1970-76 Dodge, Plymouth, A, B, E Body; Door Lock Striker Bolt; 2 Door; Each
Correct reproduction of the original door lock striker bolt designed for use on all 1970-76 Dodge and Plymouth A, B, and E body 2 door models as listed. The door lock striker bolt is manufactured to correct factory dimensions...
1970-74 Barracuda, Cuda, Challenger; Inner Fender Apron Set; 12 Piece Set; Drivers Side
Reproduction of the original inner fender apron set designed for use with 1970-74 Barracuda, Cuda, and Challenger models. Each fender apron set is manufactured in stamped steel to original factory specifications featuring...
OER reproduction windshield glass for all 1970-74 Dodge and Plymouth E-Body coupe or convertible models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against road...
1970-74 Challenger, Barracuda, Cuda; Front Windshield Glass; Coupe & Convertible; Clear
OER reproduction windshield glass for all 1970-74 Dodge and Plymouth E Body coupe or convertible models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against road...
1970 Plymouth Barracuda, Cuda; Hood Latch Assembly; EDP Coated
Reproduction of the original hood latch assembly panel designed for use with 1970 Barracuda and Cuda models. Each hood latch assembly is manufactured in stamped steel to original factory specifications featuring correct...
1970-74 Plymouth Barracuda, Cuda; Outer Door Handle Set; with Gaskets; RH & LH; Pair
Reproduction of the original outer door handles designed for use with 1970-74 Plymouth Barracuda and Cuda models. Each door handle is manufactured in quality die-cast zinc featuring a polished chrome plating replicating the...
Wiper Blade Insert; Replacement; 16" Anco Style; Each
OER reproduction Anco-style windshield wiper blade insert for various classic American vehicle models from the 1960's and up. These 16" wiper blades are manufactured from quality molded rubber as original. Refill is...