1967-75 Various GM Applications; Quadra Jet Carburetor Base Gasket; Heat Shield
Reduces heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket fits 67-75 GTO/Firebird, 67-75 Camaro, Chevelle, El...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1970-73 Trans Am; Ram Air Throttle Switch Assembly
Reproduction of the original throttle switch assembly designed for use with 1970-73 Pontiac Trans Am models. This assembly features all the components necessary to replace the original throttle switch assembly that mounts on...
1968-74 Firebird, Trans Am; Aluminum Rear Carburetor Fitting; with Angled Fitting
Reproduction of the original carburetor rear fitting designed specifically for use with 1968-74 Pontiac Firebird and Trans Am models with 326, 350, 400, and 455 motors with or without Ram Air. This fitting screws to the back...
1968-79 Accelerator Control Cable Retainer ; Various Models
OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...
1972-74 Firebird, Trans Am; Aluminum Carburetor Fitting; with 2 Angled Fittings
Reproduction of the original aluminum carburetor fitting designed for use with 1968-75 Pontiac models including Firebird and Trans Am. Each fitting features the correct GM part number # 487331 stamped on the part for...
1970-72 Camaro, Firebird; Accelerator Cable Bracket; with Holley Carburetor
Reproduction accelerator throttle cable bracket for 1970-72 Camaro and Firebird models with Holley Carburetor. This quality bracket is manufactured in stamped steel to the original factory configuration. Will fit and install...
1968-75 Firebird, Trans Am; Carburetor Rear Fitting; with Straight Fitting
Reproduction of the original aluminum carburetor fitting designed for use with 1968-75 Pontiac models including Firebird and Trans Am. This particular fitting was used on most all 1968-69 Firebird models, but can also be used...
1962-1982 GM; Carburetor, Door, Tailgate; Spring Steel Rod Clip; RH Passenger Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...