1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van...
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1970-73 Camaro, Firebird; Fuel Tank Sending Unit; 3/8" Line with 1/4" Return Line
After years of use, your fuel sending unit can wear out or stop working. When that happens, it can cause your fuel gauge not to work or even send incorrect readings to the fuel gauge. Ensure that you always know how much fuel...
1971-74 Trans-Am Throttle Cables
These throttle cables have the correct ends (carburetor and accelerator pedal) and look very close to the original.
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1967-72 Camaro, Firbeird, Nova; Fuel Tank Strap Mounting Bolt Kit ; 10 Piece Set ; Various Models
Reproduction of the original mounting bolts and hardware designed to install fuel tank mounting straps on various GM models. It's easy to replace the fuel tank straps when you have the right hardware. This set includes the...
1970-73 Camaro, Firebird; Fuel Tank Sending Unit; Single Line; 3/8"; 6 cyl, 307ci, 350ci
Reproduction of the original fuel tank sending unit designed for use with 1970-73 Camaro and Firebird models with 3/8" line. After years of use, your fuel sending unit can wear out or stop working. When that happens, it can...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
1970-72 Camaro, Firebird; Accelerator Cable Bracket; with Holley Carburetor
Reproduction accelerator throttle cable bracket for 1970-72 Camaro and Firebird models with Holley Carburetor. This quality bracket is manufactured in stamped steel to the original factory configuration. Will fit and install...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...
1970-73 Camaro, Firebird; Fuel Tank Brace Set; 4 Piece Set; EDP Coated
Reproduction of the original fuel tank brace set designed for use with 1970-73 Camaro and Firebird models. Each fuel tank brace is manufactured in stamped steel to original factory specifications featuring correct contours...