Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
Reproduction of the original outer door mirror designed for use with various 1968-72 GM models. Each mirror is precision-manufactured in high-quality die-cast zinc, replicating the original design, fit, and finish for an...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1970-72 Chevrolet Monte Carlo; Inner Fender Skirt; Liner: Well; Pair
Reproduction of the original front fender skirt designed for use with 1970-72 Chevrolet Monte Carlo models. Each fender well is manufactured with quality black semi-gloss ABS plastic and have a similar finish to GM...
1972 Monte Carlo; Front Bumper; Stamped Steel; Chrome Plated
Reproduction front bumper for 1972 Chevrolet Monte Carlo models. Manufactured in stamped steel to factory specifications, this bumper replicates the original design for proper fit, alignment, and OE authenticity. Each bumper...
OER reproduction of the original front windshield glass for use with 1968-72 Buick, Chevrolet, Pontiac, and Oldsmobile A-Body 2 door coupe models. This windshield is manufactured with tempered laminate safety glass that meets...
Wiper Blade Insert; Replacement; 16" Anco Style; Each
OER reproduction Anco-style windshield wiper blade insert for various classic American vehicle models from the 1960's and up. These 16" wiper blades are manufactured from quality molded rubber as original. Refill is...
This premium reproduction LH door glass is designed for 1970-72 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Precision-crafted with the correct...
This premium reproduction RH door glass is designed for 1970-72 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Precision-crafted with the correct...
Reproduction hinge pillar to rocker panel reinforcement panels for 1968-72 Chevelle, El Camino, 1970-72 Monte Carlo and 1971-72 GMC Sprint models. Each panel is manufactured from quality stamped steel to factory...
This premium reproduction LH door glass is designed for 1970-72 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Precision-crafted with the correct...
Reproduction door vent glass frame for 1966-67 GM A-Body coupe and convertible models (except El Camino). Manufactured to factory specifications featuring a polished chrome plated finish as original. This frame surrounds the...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
Reproduction license plate rubber bumpers for various GM models including 1967-68 Camaro front or rear. Each bumper replicates the original in fit and appearance. Will replace the original worn out or missing original rubber...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
Reproduction LH outer rocker panel for 1968-72 Chevrolet Chevelle, Pontiac GTO, Tempest, LeMans, Buick Skylark, Oldsmobile 442, Cutlass, F85, and 1970-72 Chevrolet Monte Carlo 2-door models. Manufactured to factory...
Reproduction windshield wiper arm and blade set for 1968-72 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, F85, 1970-72 Chevrolet Monte Carlo, and 1971-72 GMC Sprint...
Reproduction windshield wiper arm and blade set for 1968-72 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, F85, 1970-72 Chevrolet Monte Carlo, and 1971-72 GMC Sprint...
Original style reproduction of the outer door mirror for use with various 1968-72 GM models. Each mirror features the correct style ribbed base with "dimple" at the top of the base near the mirror head. Each mirror is...
1970-72 Chevrolet Monte Carlo, Cutlass Supreme; 2 Door Hardtop; Quarter Window Glass; RH; Clear
This premium reproduction RH quarter glass is designed for 1970-1972 Chevrolet Monte Carlo and Oldsmobile Cutlass Supreme 2 Door Hardtop models. Manufactured in factory-style clear glass to factory specifications for a...
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
Reproduction front bumper to grill filler panel for 1970 Chevelle, Malibu and El Camino and 1970-72 Monte Carlo models. Manufactured in stamped steel to factory specifications replicating the original in quality and design....
Reproduction RH manual door window regulator for 1970-72 Chevelle, Monte Carlo, GTO, Skylark, LeMans, and Grand Prix models, as well as 1970 Tempest 2-door hardtop or convertible models. Manufactured to factory...
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Factory-style reproduction of the original outer door mirror designed for use on 1968-72 GM models. This high-quality replacement features convex glass to help eliminate the passenger side blind spot, improving visibility and...
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
Reproduction of the original hood hinge assembly designed for use on various 1970 Chevrolet models. Each hood hinge is manufactured in stamped steel to original factory specifications assuring a quality replacement. Finished...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
1964-98 GM; Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each; Various Models
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
1970-72 Chevelle, El Camino, Monte Carlo; 1971-72 GMC Sprint; Hood Latch Catch Assembly; Upper
Reproduction upper hood latch catch assembly for 1970-72 Chevelle, El Camino, and Monte Carlo, as well as 1971-72 GMC Sprint models. Manufactured in stamped steel to factory specifications, this assembly replicates the...
Reproduction fender to firewall mounting brackets for 1968-72 Chevelle, El Camino, GTO, Cutlass, and 1970-81 Camaro and Firebird models. These brackets connect the front fenders to the firewall for proper alignment, strength,...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
1961-87 Buick, Chevrolet, Pontiac, Olds; Door Lock Set; with Generic Logo Keys; Bright Finish
Reproduction door lock cylinders for various 1961-87 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models as listed. Includes two door lock cylinders with bright finish face finish, two generic logo keys, cylinder...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
U-Nut Set; M6 - 1.0; Panel Range.030" to.160"; Black Phosphate; 25 Piece Set
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160"). Set of 25 u-nuts. Specifications: OE #: 11503957 Quantity:...
Reproduction windshield wiper motor arm for 1968-72 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, F85, 1970-72 Chevrolet Monte Carlo, and 1971-72 GMC Sprint models...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
Installation hardware set for various 1985-92 Camaro models including IROC-Z models. Each set includes 18 of reproduction # 11508023 bolt. Specifications: Quantity: Set of 18 Class: 9.8 Color: Black Phosphate Material: Steel...
Tapping Screw; Hex Washer Head; #8-18 x 1/2" Long; Black Oxide
Hex, washer head #8-18 x 1/2 tapping screw, in phosphate and oil coating for various applications including mounting grill to various classic vehicles Screw Specs: Description : Tapping Screw Screw Size : #8 Length : 1/2"...
Hex Bolt; 1/2"-13 x 4" LG; Gd 8; Yellow Dichromate
Hex Bolt; 1/2"-13 x 4" Lg; Gd 8; Yellow Dichromate Application 1973-1980 Chevrolet/GMC Radiator Core Support; STD Cab 1/2 & 3/4 Ton 1973-1980 Chevrolet/GMC Radiator Core Support; Crew Cab 3/4 Ton 1973-1980 Chevrolet/GMC Front...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
Bolt, 1/4-20 x 1-3/16" Dog Point Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 x 1" Pointed Tip With Hex Washer Head, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 X 7/8" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...