1962-77 GM, A, X Body; Trunk Weatherstrip; Various Models
Reproduction of the original trunk weatherstrip for a wide variety of GM models including 1962-1977 Chevy II, Nova and X Body models. Each rubber weatherstrip measures 16-1/2 feet in length, and is manufactured with correctly...
OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
1961-81 Buick, Chevy, Pontiac, Oldsmobile; Trunk Lid Rubber Bumper On Lid; Each; Various Models
Correct reproduction of the original trunk lid rubber bumper for use with various 1961-81 Buick, Chevy, Pontiac, and Oldsmobile models. Manufactured in EPDM rubber to factory specifications. Used to eliminate the trunk lid...
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1966-72 GM; Outer Mirror Mounting Set ; LH or RH ; Gasket, Bracket, Screws
Reproduction of the original style components required to replace and mount the outer door mirror on the door. Contains all the necessary hardware to install a standard outer door mirror onto either the drivers or passenger...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1966-72 Chevrolet; Standard Door Mirror Gasket
Quality reproduction outer door mirror gasket for various GM models. Manufactured to factory specifications in quality injection molded ABS, will fit original GM or reproduction mirrors. Installs between the mirror base and...
1955-72 GM; Lower Control Arm Bumpers; Polyurethane; Black; Pair
Polyurethane lower control arm bumper stops are guaranteed to last longer and perform better than O.E.M. rubber stops. Cushions impact between suspension components preventing excessive damage. Sold as a pair. 1 pair required...
Restore proper protection to your engine compartment with these factory-style OER reproduction splash apron flaps. Designed and manufactured to OE specifications, each apron set delivers an authentic fit and appearance while...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1968-72 Lower Control Arm Bumper ; Each
Reproduction of the original lower control arm bumper designed for use on various GM vehicles including 1968-69 Camaro and Firebird models. Each control arm bumper is manufactured in hard rubber featuring correct mounting...
1962-81 GM; Glove Box Door Arm Rubber Bumper
OER® reproduction of the original glove box door arm rubber bumper designed for use with various 1962-81 GM models. This rubber bumper is manufactured in EPDM rubber to the original factory configuration. Was installed on...
1965-72 Chevrolet, Oldsmobile; Trunk Lock Cylinder Gasket; Molded Rubber
Reproduction of the original trunk lock cylinder gasket designed for use on various GM models. This gasket is used to seal the trunk lock cylinder to the body. Manufactured in quality EPDM molded rubber that replicates the...
Protect your engine bay from water, salt, and road debris with these OER reproduction splash aprons. Each superior reproduction set is manufactured to original specifications, ensuring the correct fit and appearance. Designed...
1968-72 Shift Plate Seal Set ; Chevelle, El Camino, Monte Carlo ; 4 Piece Set
Reproduction of the original shift plate seals designed for use on 1968-72 Chevelle models with automatic transmissions. These seals are manufactured from die cut high grade rubber and will fit as original. 4 piece set....
1966-1979 Camaro, Impala, Nova; Rubber Side Hood Bumper; Each
Reproduction of the original style side hood rubber bumper designed for use various GM models. Over time, the rubber stoppers on your hood can wear out or deteriorate. These reproduction stoppers will help keep your hood...
1968-96 Impala, Chevelle, Corvette; Hood Rear Panel Bumper, Each, Various Models
Reproduction of the original rear hood panel bumper designed for use on various 1968-96 GM models. Exact reproduction of the original rear hood bumper used to replace the worn out or missing original. Manufactured to exact...