Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1968-72 Outer Door Mirror; Chrome: LH; Smooth Style Base; Various GM Models
Reproduction of the original outer door mirror designed for use on various 1968-72 GM models. Each mirror is manufactured in quality die-cast zinc replicating the original mirror in quality and fit. This reproduction mirror...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1968-79 Camaro, Chevelle, Impala, Nova, Ventura; Rear License Plate Bracket; with Hinge; EDP Coated
Reproduction rear license plate bracket designed for various 1968-79 GM models. This authentic OE-style bracket is manufactured from quality stamped steel and includes a spring-loaded hinged door that allows access to the...
Reproduction convertible top motor engineered to deliver consistent hydraulic pressure and dependable operation. This unit makes it easy to raise and lower your power top by replacing a weak or worn out original. Each motor...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Brand New Reproduction wiper motor built using the industry's most advanced engineering technology. Core shortages and low availability have made our brand new replacement wiper motors the high quality, low cost alternative...
1964-72 Buick, Cadillac, Chevy, Pontiac, Oldsmobile; Convertible Top Latch Knuckle Hook; Each
Reproduction of the original latch knuckle hook designed for use with various GM convertible models. This component secures the convertible top to the upper windshield header, ensuring a proper seal and stable fit. Each...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1967-69 Camaro, Firebird, 1968-72 Chevelle; Convertible Top Frame Pivot Bolt and Bushing Set
Reproduction of the rear control link bolt and bushing set designed for use with 1967-69 Chevrolet Camaro, Pontiac Firebird, and 1968-72 Chevrolet Chevelle convertible models. This complete set includes all required rear...
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
Reproduction of the original convertible top latch knuckle designed for use with a variety of 1964-72 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile convertible models. Manufactured in quality zinc die-cast metal, each...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
Reproduction of the original convertible top latch knuckle designed for use with a variety of 1964-72 GM convertible models. Manufactured in quality zinc die-cast metal, each knuckle is built to OE factory specifications for...
Reproduction of the original hood hinge assembly designed for use on various 1970 Chevrolet models. Each hood hinge is manufactured in stamped steel to original factory specifications assuring a quality replacement. Finished...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...