Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1968-72 Outer Door Mirror; Chrome: LH; Smooth Style Base; Various GM Models
Reproduction of the original outer door mirror designed for use on various 1968-72 GM models. Each mirror is manufactured in quality die-cast zinc replicating the original mirror in quality and fit. This reproduction mirror...
1955-82 Spare Tire Hold Down Nut; 5/16"-18 Thread; 3.88" Wide; Zinc Finish
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1969-87 GM; Door Hinge Repair Set ; Except with 15mm OD Bushings
Reproduction of the original door hinge components for use on various GM models. Repair the broken door hinges with this comprehensive repair set. Each repair kit includes 4 properly hardened shoulder pivot pins and 8...
OER reproduction front windshield glass for use with various 1971-76 Buick, Chevrolet, Pontiac, and Oldsmobile B and C Body 2 & 4 door, hardtop, sedan, and station wagon models without a built in antenna. This windshield is...
OER reproduction front windshield glass for use with various 1971-76 Buick, Chevrolet, Pontiac, and Oldsmobile B and C Body 2 & 4 door, hardtop, sedan, and station wagon models without a built in antenna. This windshield is...
Replace the worn or rusted out rear convertible tack strip floating rear bow with this quality reproduction. Also referred to as the rear tacking rail or trimstick, this one-piece tack strip bow mounts below the rear window...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1970-81 Camaro, Firebird, Impala; Upper Front Door Hinge; Passenger Side; Various Models
This OER® reproduction door hinge will allow your door to work properly again! The 1970-81 doors were extremely heavy and hard on the original hinges. A new set of hinges will help your doors to open and close the way the...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
OER reproduction front windshield glass for use with various 1971-76 Buick, Chevrolet, Pontiac, and Oldsmobile B and C Body 2 & 4 door, hardtop, sedan, and station wagon models. This windshield is manufactured with tempered...
OER reproduction front windshield glass for use with various 1971-76 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile B-Body 2 & 4 door, coupe and hardtop models. This windshield is manufactured with tempered laminate...
1970-75 Camaro, Firebird, Impala; Outer Door Handle; Die-Cast Chrome; Passenger Side
Reproduction of the original outer door handle designed for use with various 1970-75 GM vehicles including Camaro, Firebird, Impala, and various other models. Each outer door handle is manufactured to factory specifications...
1971-75 Impala, 1971-76 GM Full-Size; Convertible; Front Door Glass; RH; Clear
Reproduction door glass for various 1971-76 GM models. Manufactured to factory specifications featuring correct glass shape, and contours for proper fitment and appearance. Replaces NAGS # DD04631. Note: Shipped oversize....
1971-73 Impala, GM Full-Size; 2 Door Hardtop; Front Door Glass; LH; Clear
Reproduction door glass for various 1971-73 Chevrolet and GM 2-door hardtop models. Manufactured to factory specifications featuring correct glass shape, and contours for proper fitment and appearance. Replaces NAGS #...
1971-73 Impala, GM Full-Size; 2 Door Hardtop; Front Door Glass; LH; Light Green Tint
Reproduction door glass for various 1971-73 Chevrolet and GM 2-door hardtop models. Manufactured to factory specifications featuring correct glass shape, and contours for proper fitment and appearance. Replaces NAGS #...
1971-75 Impala, 1971-76 GM Full-Size; Convertible; Quarter Glass; RH; Custom Gray Tint
Reproduction rear quarter glass for various 1971-76 GM models. Manufactured to factory specifications featuring correct glass shape, and contours for proper fitment and appearance. Replaces NAGS # DQ04633. Note: Shipped...
1971-75 Impala, 1971-76 GM Full-Size; Convertible; Quarter Glass; LH; Custom Gray Tint
Reproduction rear quarter glass for various 1971-76 GM models. Manufactured to factory specifications featuring correct glass shape, and contours for proper fitment and appearance. Replaces NAGS # DQ04633. Note: Shipped...
1971-75 Impala, 1971-76 GM Full-Size; Convertible; Quarter Glass; LH; Clear
Reproduction rear quarter glass for various 1971-76 GM models. Manufactured to factory specifications featuring correct glass shape, and contours for proper fitment and appearance. Replaces NAGS # DQ04633. Note: Shipped...
1971-75 Impala; 1971-76 GM B-Body Convertible; Rear Top Bow; #2 Position; Behind Header Bow
Reproduction #2 convertible top bow (the next one back from the header bow) for 1971-76 GM full size models. Each bow is drilled and tapped for your ball joint pivot brackets (sold separately) and have the proper dimples in...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
1971-75 Impala, 1971-76 GM Full-Size; Convertible; Quarter Glass; LH; Light Green Tinted
Reproduction rear quarter glass for various 1971-76 GM models. Manufactured to factory specifications featuring correct glass shape, and contours for proper fitment and appearance. Replaces NAGS # DQ04633. Note: Shipped...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
Reproduction license plate rubber bumpers for various GM models including 1967-68 Camaro front or rear. Each bumper replicates the original in fit and appearance. Will replace the original worn out or missing original rubber...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
Reproduction of the original style outer door mirror designed for use with various 1971-79 Buick, Chevrolet, Pontiac, and Oldsmobile models. Each mirror is manufactured in quality die-cast zinc and features a chrome plated...
Reproduction of the original convertible rear glass window control arms designed for use with 1971-76 GM Full Size convertible models as listed. These arms control the movement of the window as the top is lowered into the...
Original style reproduction of the outer door mirror for use with various 1968-72 GM models. Each mirror features the correct style ribbed base with "dimple" at the top of the base near the mirror head. Each mirror is...
1971-75 Chevrolet and Oldsmobile; Hood Release Cable and Handle; 2 Piece Style
Reproduction hood latch release cable and handle assembly for 1971-75 Chevrolet and Oldsmobile models. This cable is manufactured to factory specifications and replicates the original in quality, design, and fitment. Includes...
Reproduction bronze and steel convertible top frame bushing set designed for use with various 1971-76 GM full size models. A fresh set of top frame bushings can restore smooth operation to your convertible top, reducing wear...
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1971-76 Impala, Caprice, LeSabre, Delta 88, Catalina; Convertible Rain Gutter Wire
Reproduction of the original style rain gutter wire designed for use with various 1971-76 GM full size models as listed. This wire is inserted into the convertible top well liner to provide support for the rain gutter. An...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Zinc plated tapping screw is needed. Sold individually.
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
Original style replacement outer door mirror for 1968-72 models, features convex glass. The convex glass helps eliminate the passenger side blind spot. Each rear view mirror features the correct ribbed base and comes with a...
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
Reproduction of the original style third bow plastic guide designed for use with 1971-76 GM full size convertible models. This guide mounts with screws onto the third bow and ensures the side rails of the top frame run...
1971-76 Impala, Caprice, Catalina, Delta 88; Convertible Drive Cable; Blue; LH Driver Side
Reproduction of the original convertible top drive cable designed to fit various 1971-76 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile Full Size B-body and C-body models as listed. This cable is designed for use with...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
1971-76 Impala, Caprice, Catalina, Delta 88; Convertible Drive Cable; Black; RH Driver Side
Reproduction of the original convertible top drive cable designed to fit various 1971-76 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile Full Size B-body and C-body models as listed. This cable is designed for use with...
Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Reproduction of the original convertible top actuator gear designed for use with various 1971-76 GM full size models. This small gear is an exact replacement for the factory unit and is ideal for repairing worn or damaged...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Reproduction rear glass window brackets that attach to the lower left and right corners of the rear glass window on the convertible top. The control link support arms connect to this bracket. The control link support arms, or...
5/16" X 18 X 1-1/4" Hex Washer Head Spin Lock Bolt; Phospate Coating
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
5/16" X 18 X 1-1/4" Hex Washer Head Spin Lock Bolt; Phospate Coating; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...