1959-81 GM; Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for use on various GM models. Manufactured from durable EPDM rubber, this spacer was originally installed to correct uneven ride height on vehicles that did not...
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Commonly referred to as a trailing arm, this component mounts between the rear axle housing and the center...
1960-72 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Rear Control Arm; LH Driver Side; EDP Coated
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Also known as a trailing arm, this component mounts between the rear axle housing and the center crossmember to...
1960-72 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Rear Control Arm; RH Passenger Side; EDP Coated
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Also known as a trailing arm, this component mounts between the rear axle housing and the center crossmember to...
Reproduction front crossmember for 1967-72 Chevrolet and GMC C10 pickup truck models. Each crossmember is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic appearance...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1963-96 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Lower Control Arm Shaft Kit; 2 Wheel Drive
Reproduction control arm shaft kit, precision engineered and rigorously tested to provide a dependable replacement for the original equipment shaft. Designed as a direct fit component, this shaft installs and functions...
1971-72 Chevrolet/GMC; 2 Wheel Drive; 1/2 Ton Truck; Upper Ball Joint; with 1/2" Threads
Reproduction upper ball joint for various 1971-72 Chevrolet and GMC 1/2 ton (2 wd) models. Two required per vehicle. Sold individually. Fits left hand (driver side) or right hand (passenger side). Chevrolet Truck...
1971-95 Chevrolet/GMC 2 Wheel Drive Truck.003 Oversize Lower Ball Joint
If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about rebuilding your front suspension. This.003 oversize ball joint is designed to be pressed into place in the lower...
1963-72 Chevy, GMC Pickup; C10; C20; C30; Bracket; Front Sway Bar to Frame; Stock Height
This 1963-72 front sway bar to frame bracket is designed for a factory/stock height pickup. For trucks with air bag suspension we also recommend using stock height brackets. Sold individually, fits LH or RH side of the...
This lowered front sway bar bracket will provide more ground clearance and is recommended for trucks lowered 3" or more. The bracket pulls the bar up towards the frame to achieve additional ground clearance. For trucks with...
Reproduction molded rubber front coil spring insulator designed to mount between the coil spring and the frame on various 1949-2002 vehicles. This insulator prevents metal to metal contact, reducing noise, vibration, and...
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Commonly referred to as a trailing arm, this component mounts between the rear axle housing and the center...
1971-72 Chevy, GMC C10 Pickup; 1/2 Ton 2WD, Blazer, Jimmy, Suburban; Drop Spindles; 2-1/2"
Lower your 1971-72 Chevy or GMC 1/2 ton 2WD truck 2-1/2" with our cast iron disc brake drop spindles. These will enhance your stopping power, steering and handling, and give your truck a better stance. Cast from the highest...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
Reproduction rear crossmember with factory style holes for connecting the LH and RH frame rails at the rear of the frame. A good way to replace a damaged crossmember on a rusty or wrecked truck frame with an original...
1974-78 Mustang II; Front Sway Bar Kit; 3/4" ; 43-1/4" Wide; for Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks equipped with standard width crossmember Mustang II front suspension systems. This sway bar is engineered to reduce body roll, under steer, and over steer during...
Reproduction control arm shaft kit, precision engineered and rigorously tested to deliver a dependable replacement for the original equipment shaft. This direct fit replacement installs and functions exactly like the factory...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
1970-93 Chevy, GMC, Ford, Dodge Truck; Upper Ball Joint; RH or LH; Each
OER® Authorized reproduction of the original type upper ball joint designed for use with a wide variety of 1970-91 GM, 1971-80 Ford, 1972-93 Dodge and Plymouth truck models. The upper ball joint is manufactured to factory...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4" to 4" inclusive. These heat treated washers are for general purpose and structural use. For use...
Reproduction bracket designed to mount the upper control arm to the frame on 2 wheel drive 1/2 ton Chevrolet and GMC pickup, Blazer, and Jimmy models from 1963-72. Manufactured from heavy duty stamped steel just like the...
Reproduction center transmission mount crossmember with factory style holes for connecting the LH and RH frame rails at the center of the frame and providing a place to mount the transmission. A good way to replace a damaged...
Reproduction front crossmember with factory style holes for connecting the LH and RH frame rails at the front of the frame. Also a good way to save a truck by replacing the damaged crossmember on a rusty or wrecked truck...
Reproduction rear trailing arm mount crossmember with factory style holes for connecting the LH and RH frame rails at the rear of the frame and providing a place to mount the trailing arm braces. A good way to replace a...
1963-72 Chevy, GMC; Pickup, Blazer, Jimmy, Suburban; Upper Control Arm Mount Bracket; LH Driver Side
Reproduction bracket designed to mount the upper control arm to the frame on 2 wheel drive 1/2 ton Chevrolet and GMC pickup, Blazer, and Jimmy models from 1963-72. Manufactured from heavy duty stamped steel just like the...
Reproduction rear axle crossmember with factory style holes for connecting the LH and RH frame rails at the rear of the frame on coil spring trucks. A good way to replace a damaged crossmember on a rusty or wrecked truck...
Reproduction engine mount/control arm mount crossmember with factory style holes for connecting the LH and RH frame rails and mounting the engine and the control arms at the front of the frame. A good way to save a truck by...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...