Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1967-74 Dodge, Plymouth; A, B-Body; Outer Door Mirror; Single Post; with Hardware; RH or LH; Each
Reproduction of the original outer single post door mirror for 1967-74 Dodge and Plymouth A-Body or 1968-70 Dodge and Plymouth B-Body models. Each outer door mirror is manufactured in die-cast zinc featuring a bright chrome...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Reproduction of the original front windshield glass for use with all 1967-76 Dodge and Plymouth A-Body models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against...
Wiper Blade Insert; Replacement; 16" Anco Style; Each
OER reproduction Anco-style windshield wiper blade insert for various classic American vehicle models from the 1960's and up. These 16" wiper blades are manufactured from quality molded rubber as original. Refill is...
1965-74 Chrysler, Dodge, Plymouth; Windshield Washer Pump; Replacement
Replacement style windshield washer pump assembly designed for use with the applications listed below. The windshield washer pump circulates water from the windshield washer jar to the washer nozzles. This is a replacement...
1967-76 Dart, Barracuda, Valiant, Duster; Windshield Wiper Arms; Anco Style; Pair
Reproduction of the original Anco style wiper arms designed for use with 1967-76 Dodge and Plymouth A-body models. Each wiper arm is manufactured from stamped and formed polished stainless steel featuring a chrome plated cap...
1970-76 Dodge Dart, Duster, Valiant; Rallye Sport Outer Door Mirror; Primer; RH Passenger Side
Reproduction Rallye outer door mirror for 1970-76 Dodge, Plymouth A-body models. Each mirror is manufactured to correct factory specifications and offered in primer. Paint as required. Fits the RH passenger side. {fitment}
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
Reproduction outer door handles for various 1971-76 Dodge and Plymouth A-Body models and 1972-93 Dodge D/W Series trucks. Each door handle is manufactured in quality die-cast zinc featuring a polished chrome finish...
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
1968-71 Dodge; Plymouth; Chrysler; Windshield Wiper Motor; 2-Speed; Brand New
New windshield wiper motor for various 1968-71 Mopar models. Brand new tooling for a crisp and clean look. Meticulously engiineered as an improvement over the original design. The motor gears are designed with a stronger,...
1964-98 GM; Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each; Various Models
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
1967-74 Mopar; Windshield Washer Nozzle Kit ; A-Body
Reproduction of the original components required to replace the windshield washer nozzles and hardware for 1967-74 Mopar A Body models. Manufactured to original specifications and features quailty plating for an unmatched fit...
1966-76 Dodge/Plymouth A & B-Body; Mount Pad; For Outer Remote Door Mirror; Each
Reproduction of the original style outer door mirror pads designed for use with 1967-76 Dodge, Plymouth A Body, and 1966-70 B Body models as listed. Each gasket is manufactured with modern, firm 80 durometer EPDM rubber...
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
1966-74 Dodge, Plymouth A, B, E Body; Remote Mirror Retainer Clip
Reproduction of the original remote mirror retainer clip designed for use with 1966-74 Dodge and Plymouth A, B, and E Body models with remote mirror. Each mirror retainer clip is designed and manufactured in stamped steel...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
U-Nut Set; M6 - 1.0; Panel Range.030" to.160"; Black Phosphate; 25 Piece Set
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160"). Set of 25 u-nuts. Specifications: OE #: 11503957 Quantity:...
Installation hardware set for various 1985-92 Camaro models including IROC-Z models. Each set includes 18 of reproduction # 11508023 bolt. Specifications: Quantity: Set of 18 Class: 9.8 Color: Black Phosphate Material: Steel...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
Bolt; 1/2"-13 x 5" Lg Hex Head Cap Screw; Grade 8
1/2"-13 x 5" Hex Head Cap Screw; Grade 8
Bolt; Hex Head; 5/16"-24 x 3.0"; Grade 5; Cap Screw; Silver Zinc
5/16"-24 x 3.0" Lg Hex Head Cap Screw, Grade 5, Zinc plated
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a set of 10, refer to part...
Bumper Bolt with Stainless Steel Head; Zinc Plated; 7 /16"-14 x 1" Bolt with Hex Nut
Reproduction bumper bolt with hex nut manufactured in zinc plated material offering an authentic appearance and fitment. Measures 7/16" -14 x 1" and features a stainless steel cap. Head diameter 31/32". Each bolt will replace...
1970-2002 GM; Hood Insulation Fastener; Each
Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...
GM, Ford, Chrysler; ANCO Windshield Wiper Blades; 15"; Polished Stainless Steel; Pair
OER reproduction "Anco style" wiper blades for use with various GM, GMC, Chrysler, Plymouth, Dodge, AMC, Ford, and Studebaker models. Each blade features a polished stainless steel body with the correct rubber insert,...
Phillips Oval Head Chrome Trim Screw; #8 x 3/4"; with Undersized # 6
Phillips Oval Head Tap Screw # 8 X 3/4 Chrome # 6 Head Specifications: Screw Size : #8 Length : 3/4" Head Style : Phillips Oval Point Type : A/AB Head Size : #6 Finish : Chrome
U-Nut #10 Screw Size; Panel Clip; Phosphate; Each
Correct U-nut used on various GM vehicles including for the glove box of 1967-72 Chevrolet and GMC trucks. This part is original equipment style for multiple GM applications, and it can be used for a variety of other...
Reproduction flat style phillips head machine screws for latches and strikers on various classic makes and models. Fits the door striker on 1947-51 Chevrolet and GMC truck models. Fits the door latch on various 1966-74 Dodge...
Sheet Metal Screw #8 x 5/8" Hex Head Black
Specialty screw used for many GM sheet metal applications. This black phosphate hex screw is designed for use when installing fenders and other sheet metal components to the body. For general use #8 x 5/8" hex head. Sold...
1966-74 Dodge/Plymouth A & B-Body; Exterior Door Mirror Set; LH Remote/RH Manual; Round Style; Pair
OER reproduction of the original outer door mirrors manufactured in high quality die-cast zinc material just like the original mirrors. For use with A and B-body applications. Includes all necessary installation screws,...
OER reproduction of the Anco Rain-Master Style full frame, medium profile windshield wiper blades with push-button release for refill. These 16" Anco style wiper blades are manufactured from stamped stainless steel with a...
1967-76 Dodge, Plymouth A-Body; Front Windshield Glass; 2 Door Hardtop & Convertible; Clear
Reproduction of the original front windshield glass for use with all 1967-76 Dodge and Plymouth A-Body models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against...
Bumper Bolt and Hex Nut; with Stainless Steel Head; Zinc Plated; 7 /16"-14 x 1-1/4"
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Universal Hex Head Sems Bolt; M6-1.0 X 20mm; Black Phosphate; Each
Black phosphate hex head Sems metric bolt, that measures M6-1.0 X 20 mm to install and secure various components Specifications: Quantity: Individual Bolt Class: 9.8 Color: Black Phosphate Material: Steel Specs: M6 -1.0 X 20...
1969-2002 Nylon Rod Clip, Fits 5/32" Rod Diameter; 1/4" Hole Size; LH Driver Side; Varius Models
Reproduction of the clip that retains the two inner door lock rods. This nylon clip joins the horizontal rod from the door latch with the verticle rod that the door lock knob screws on to. Sold individually. One required per...
Windshield Wiper Blades; 16" long; Aero Style; For 1/4" (7mm) Bayonet Style Arms; Pair
Authentic reproduction of the stainless steel ANCO Rain-Master (original ANCO part # 816) "Aero" Anti Wind-Lift Wiper Blades designed to fit 1/4" (7mm) wide bayonet style wiper arms. Popularized in the 1960's and 70's to...
Black phosphate hex head Sems metric bolt designed to OE standards for securing various underhood and body components. Measuring M6-1.0 X 30 mm, this high-strength fastener is manufactured in steel and finished in black...
Correct style push-in clear retainer clip designed for use with various GM applications including 1979-2002 Camaro and 1976-2002 Firebird models. Manufactured to replicate the original GM design in a clear injection molded...
1968-81 GM; Door Glass Roller Washer; Various Models
Reproduction plastic washer that pushes through the door glass on various 1968-81 GM models. Exact reproduction of the original door glass roller washer. Sold individually. Use as required. Replaces OE # 4491087. {fitment}
License Plate Mounting Nut and Screw Set; 10 Piece Set; Front and Rear
Correct replacement license plate nylon nut insert & slotted pan head screw used on various GM vehicles. These nuts push into the square hole in a bracket or on valance panel or other sheet metal part to provide a secure...