Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Reproduction of the original remote outer door mirror designed for use on various 1970-81 GM models including Camaro, Firebird, Nova, LeMans, GTO, Cutlass, 442, and others. Each mirror is manufactured from high-quality...
This convertible is crafted from Pinpoint vinyl, a heavy-duty vinyl composite material. It consists of an outer layer of PVC and an inner layer of dyed, 100-percent-cotton sateen. This vinyl design is original to most...
This convertible is crafted from Pinpoint vinyl, a heavy-duty vinyl composite material. It consists of an outer layer of PVC and an inner layer of dyed, 100-percent-cotton sateen. This vinyl design is original to most...
This convertible is crafted from Pinpoint vinyl, a heavy-duty vinyl composite material. It consists of an outer layer of PVC and an inner layer of dyed, 100-percent-cotton sateen. This vinyl design is original to most...
This convertible is crafted from Pinpoint vinyl, a heavy-duty vinyl composite material. It consists of an outer layer of PVC and an inner layer of dyed, 100-percent-cotton sateen. This vinyl design is original to most...
1971-72 Oldsmobile Cutlass; Rear Bumper; Chrome; Y79 Models With Dual Exhaust Cut-Outs
Reproduction rear bumper for 1971-72 Oldsmobile Cutlass Y79 models equipped with dual exhaust cut-outs. Manufactured in stamped steel to factory specifications, this bumper replicates the original design for a proper fit and...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1970-81 Camaro, Firebird, Impala; Upper Front Door Hinge; RH Passenger Side; Various Models
This OER® reproduction door hinge restores proper door operation on 1970-81 models. The factory doors were extremely heavy and often caused the original hinges to wear or sag over time. Replacing them with this...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
Replace the worn or rusted out rear floating bow or rear tacking rail with this quality reproduction. This 1-piece tack strip, also referred to as a trimstick mounts to the frame just behind the quarter glass and secures the...
1968-72 Olds F85, Cutlass, 442; 2 Door Hardtop and Sedan; Back Glass; Smoke Gray Tint
This premium reproduction back glass is designed for 1968-72 Oldsmobile F-85, Cutlass, and 442 2 Door Hardtop and Coupe (with post) models. Manufactured in factory-style smoke gray tinted glass to original specifications for...
OER reproduction of the original front windshield glass for use with 1968-72 Buick, Chevrolet, Pontiac, and Oldsmobile A-Body 2 door coupe models. This windshield is manufactured with tempered laminate safety glass that meets...
This premium reproduction LH door glass is designed for 1970-72 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Precision-crafted with the correct...
This premium reproduction RH door glass is designed for 1970-72 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Precision-crafted with the correct...
Reproduction hinge pillar to rocker panel reinforcement panels for 1968-72 Chevelle, El Camino, 1970-72 Monte Carlo and 1971-72 GMC Sprint models. Each panel is manufactured from quality stamped steel to factory...
This premium reproduction LH door glass is designed for 1970-72 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Precision-crafted with the correct...
Reproduction door vent glass frame for 1966-67 GM A-Body coupe and convertible models (except El Camino). Manufactured to factory specifications featuring a polished chrome plated finish as original. This frame surrounds the...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
This premium reproduction RH quarter glass is designed for 1968-72 Buick Skylark, GS, Chevrolet Chevelle, Malibu, Oldsmobile Cutlass, and Pontiac Tempest, LeMans, GTO Convertible models, plus 1970-72 Chevrolet Monte Carlo...
This premium reproduction LH quarter glass is designed for 1968-72 Buick Skylark, GS, Chevrolet Chevelle, Malibu, Oldsmobile Cutlass, and Pontiac Tempest, LeMans, GTO Convertible models, plus 1970-72 Chevrolet Monte Carlo...
Reproduction LH outer rocker panel for 1968-72 Chevrolet Chevelle, Pontiac GTO, Tempest, LeMans, Buick Skylark, Oldsmobile 442, Cutlass, F85, and 1970-72 Chevrolet Monte Carlo 2-door models. Manufactured to factory...
Reproduction windshield wiper arm and blade set for 1968-72 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, F85, 1970-72 Chevrolet Monte Carlo, and 1971-72 GMC Sprint...
Reproduction windshield wiper arm and blade set for 1968-72 Chevrolet Chevelle, El Camino, Pontiac GTO, Tempest, LeMans, Buick Skylark, GS, Oldsmobile Cutlass, 442, F85, 1970-72 Chevrolet Monte Carlo, and 1971-72 GMC Sprint...
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
1968-72 GM A-Body; Convertible Top Hydraulic Hose Set; with Power Top; White Hose
Reproduction of the original hydraulic hose set designed for use with 1968-72 GM A-body convertible models as listed. Original hoses for these models are nearly impossible to locate, making this reproduction set the perfect...
This premium reproduction LH quarter glass is designed for 1968-72 Buick Skylark, GS, Chevrolet Chevelle, Malibu, Oldsmobile Cutlass, and Pontiac Tempest, LeMans, GTO Convertible models, plus 1970-72 Chevrolet Monte Carlo...
This premium reproduction LH quarter glass is designed for 1968-72 Buick Skylark, GS, Chevrolet Chevelle, Malibu, Oldsmobile Cutlass, and Pontiac Tempest, LeMans, GTO Convertible models, plus 1970-72 Chevrolet Monte Carlo...
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
1968-72 GTO, Chevelle, Monte Carlo, Skylark, Cutlass; Quarter Window Regulator; Manual; LH
Reproduction quarter window regulator for 1968-72 GM A-body models. Each quarter window regulator will install on coupe or convertible models. Completely assembled and ready to install. Fits the LH, driver side. {fitment}
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Reproduction hood hinge assembly for 1969-72 Cutlass, 442, W30, W31, Rally 350 models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the hood spring when installing...
Reproduction factory style hood hinge for 1969-72 Oldsmobile Cutlass, 442, W30, W31 Rally 350 and F85 models. Replace the worn out hinge and get the proper hood alignment on factory steel or Ram Air hood. {specs} {fitment}
Inside hood latch release handle cable with handle for various 1969-72 GM applications including, Oldsmobile Cutlass, Pontiac GTO models. It has a black housing with a chrome knob, border and lettering that mounts underneath...
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
1964-98 GM; Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each; Various Models
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Reproduction fender to firewall mounting brackets for 1968-72 Chevelle, El Camino, GTO, Cutlass, and 1970-81 Camaro and Firebird models. These brackets connect the front fenders to the firewall for proper alignment, strength,...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
1971?73 Buick & Oldsmobile License Plate Bracket; except Station Wagon Models
Upgrade your restoration or replace a damaged original with this high-quality reproduction license plate bracket, designed specifically for 1971?1973 Buick and Oldsmobile models, excluding station wagons. Manufactured to...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
1961-87 Buick, Chevrolet, Pontiac, Olds; Door Lock Set; with Generic Logo Keys; Bright Finish
Reproduction door lock cylinders for various 1961-87 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile models as listed. Includes two door lock cylinders with bright finish face finish, two generic logo keys, cylinder...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...