1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1970 Impala, Bel Air, Caprice Chevelle, El Camino; Hood Hinge; LH Passenger Side; EDP Coated
Reproduction of the original hood hinge assembly designed for use on various 1970 Chevrolet models. Each hood hinge is manufactured in stamped steel to original factory specifications assuring a quality replacement. Finished...
Reproduction cowl induction hood door for 1970-72 Chevelle and El Camino Super Sport models equiped with the factory cowl induction option. This die cast hood door is manufactured to factory specifications featuring the...
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 8 Piece Set
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"- 16 x 1" specs....
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 10-Pieces
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Hood Insulation Fastener Set; 5/16" Stem Diameter; 3/4" Stem Length; 1-3/4" Head Diameter; 20-Pieces
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
1970-2002 GM; Hood Insulation Fastener; Each
Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...
1963-72 Buick, Chevrolet, Oldsmobile, Pontiac; Hood Hinge Spring; For Steel Hoods
Reproduction hood hinge spring for various GM models including Chevelle, Camaro, Impala, Firebird and other various GM models. Each spring is designed and manufactured to exact factory specifications for the models listed...
1958-77 GM; Hood Adjuster Bolt and Nut Set ; 5/16"-18 x 1-3/8"; Various Models
Reproduction of the original hood stop bolt and nut set designed for use on various 1958-77 GM models. This bolt and nut set will keep the hood adjusted to the proper height. These 5/16"-18 x 1-3/8" bolts include the correct...
1970-72 Chevelle, Malibu, El Camino; 1971-72 GMC Sprint; Hood Latch Assembly; Replaces GM# 3975406
Reproduction hood latch assembly for 1970-72 Chevelle, Malibu and El Camino models. Each hood latch assembly is manufactured in stamped steel to factory specifications featuring correct contours for an authentic appearance...
1970 Impala, Bel Air, Caprice Chevelle, El Camino; Hood Hinge; RH Passenger Side; EDP Coated
Reproduction of the original hood hinge assembly designed for use on various 1970 Chevrolet models. Each hood hinge is manufactured in stamped steel to original factory specifications assuring a quality replacement. Finished...
1969-76 Camaro, Corvette, Trans Am; Cowl Induction Solenoid
Reproduction cowl induction solenoid assembly which allows the hood valve assembly to open and shut when the accelerator is depressed. Manufactured to exact specifications, each solonoid will install and function same as...
Reproduction cowl induction hood door support brackets for 1970-72 Chevelle and El Camino Super Sport models equiped with the factory cowl induction option. These die cast support brackets are manufactured to factory...
1970-72 Chevrolet Chevelle, El Camino, Monte Carlo; Hood Release Handle
Reproduction of the original hood latch release rod handle designed for use with 1970-72 Chevelle, El Camino and Monte Carlo models. Each rod is manufactured in quality stamped steel replicating the original in configuration,...
Reproduction hood pin rubber gasket found on models with hood pins. Each gasket is die-cut to proper dimension. Will also fit a wide variety of aftermarket hood pins. Sold individually. Use as required. Check measurements...
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1965-1970 GM; Hood Insulation Fastener Set; 20 Piece Set; Various Models
Reproduction of the original hood insulation fasteners designed for various 1965-69 GM models. Manufactured in injection molded ABS plastic to replace OE part number # 3909199. These are an exact copy of the OE retainer for...
Chrome Hood Pin Set; Flip Over Style; With Landyards
Hood pin set for various models. Hood pins are necessary for the attachment of fiberglass or lift off hoods and may be installed for extra security on factory hoods. This universal style hood pin set includes pine, cables....
Chrome Hood Pin Set; Hair Pin Style
Reproduction of the deluxe style hood pin set with hair pin design. Set includes all necessary components to replace the original hood pin including 2 hairpin style hood pins, 2 plates, 4 bolts and 8 mounting screws. Lanyards...
Hood Pin Kit; with Lanyard; Hair Pin Style; Universal Fit
Hood pins are necessary for the attachment of fiberglass or lift off hoods and may be installed for extra security on factory hoods. Each set uses the two piece hairpin style pins ideal for installations where a...