1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van...
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Reproduction carburetor to accelerator lever cable for 1970 Camaro (4 bbl), 1971-73 Camaro with (350 4 bbl.), and 1970-72 Chevelle (with 396, 454). Each cable is manufactured to correct length and specifications. Replaces...
1971-72 Chevrolet Chevelle; 20 Gallon Fuel Tank; w/ Filler Neck; w/ Three Vent Pipes
Reproduction fuel tank for 1971-72 Chevrolet Chevelle models. This reproduction fuel tank is manufactured in quality stamped steel featuring a zinc coating for rust and corrosion prevention. This is a 20 gallon fuel tank that...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1968-72 Camaro, Impala, Nova; Holley Throttle Cable Bracket
Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1968-72 Chevrolet Chevelle, Malibu; Big Block; Quadrajet; Accelerator/Throttle Cable
Replacement accelerator/throttle cable for 1968-72 Chevrolet Chevelle and Malibu models. This cable is 23.5 inches long and is for big block applications. GM#'s 396454, 3972679. {specs} {fitment}
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Reduce heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket and shield was original equipment for most 1970 Chevrolet...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1971-72 El Camino, Sprint; 20 Gallon Fuel Tank; w/ Filler Neck; w/ Vent Pipes
Reproduction fuel tank for 1971-72 Chevrolet El Camino and GMC Sprint models. This reproduction fuel tank is manufactured in quality stamped steel featuring a zinc coating for rust and corrosion prevention. This is a 20...
1965-74 Holley; Carburetor Heat Shield; 4 Barrel with 396,454 Engine
OER® reproduction carburetor heat shield for all GM models with a Holley 4 bbl carburetor. This heat shield will help cool the intake charge for better performance. Original for 1970 396ci & 454ci with Special...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1971-72 Chevrolet Chevelle; Cruise Control; Servo Actuator Cable
Replacement cruise control servo actuator cable for 1971-72 Chevrolet Chevelle models. This cables goes from the cruise control vacuum servo to the carburetor. Used with all engines. Sold individually. {fitment}
1970-72 Chevelle, El Camino, Monte Carlo, GTO, LeMans; 1970 Tempest; Accelerator Pedal Assembly
Reproduction accelerator pedal assembly for 1970-72 Chevelle, El Camino, Monte Carlo, GTO, and LeMans models, as well as 1970 Tempest. Manufactured to factory specifications, this assembly includes the pedal pad, mounting...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1968-72 Chevrolet Chevelle, 1970-72 Monte Carlo; Small Block engines; Accelerator/Throttle Cable
Replacement accelerator cable for 1968-72 Chevorlet Chevelle and 1970-72 Monte Carlo models. Extends from the carburetor to the accelerator pedal lever. Sold individually. GM# 3973862. {specs} {fitment}
1968-72 Chevelle, GTO, Cutlass, GS; Fuel Tank Mounting Straps; Pair; Except Station Wagon Models
Reproduction of the original style fuel tank mounting straps for various 1968-72 GM A-body models including Chevelle, El Camino, GTO, LeMans, Gran Sport and Cutlass models. Each strap is manufactured in quality stamped steel...
Stainless steel fuel tank mounting straps for various 1968-72 GM A-body models including Chevelle, El Camino, GTO, LeMans, Gran Sport and Cutlass models. Each strap is manufactured in quality stainless steel with all correct...
This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...
1969-81 Fuel and Brake Line Clip ; Dual Line 3/8" and 1/4"
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
Fuel and Brake Line Clip Set ; Dual Line 3/8" and 1/4" ; 7 Piece Set
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1968-79 Accelerator Control Cable Retainer ; Various Models
OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...
1967-72 GM; Brake or Return Fuel Line Clip; Under Body; R-Profile; 3/16"; Each
Reproduction of the original under body brake and fuel line clip for various 1967-72 GM models. This clip secures the brake and fuel line to the under body to keep the brake and fuel lines out of harm's way. This is a 3/16"...
1967-77 GM Pedal Pad Kit With Disc Brake Emblem; Auto Trans; 6-Piece Kit
Reproduction of the original pedal pads designed for 1967-68 Camaro, Firebird and a variety of additional GM models as listed. This pedal pad set is designed to replace the worn out original pads for models with disc brakes...
1968-81 GM Pedal Pad and Trim Plate Kit; Disc Brake; Auto Trans; 6 Piece Kit; Various Models
Reproduction of the original pedal pads and pedal pad trim plates to fit various GM models. This pedal pad set is designed to replace the worn out original pads for models equipped with disc brakes and automatic transmission....
1967-77 GM Pedal Pad Kit - Auto Trans - 6 Piece Kit
This complete kit is designed to replace pedal pads and trim plates on a variety of Chevrolet models including 1967-68 Camaro with drum brakes and an automatic transmission as well as a variety of additional GM models as...
Reproduction rubber bumper for various GM applications. Each bumper is manufactured in EPDM rubber to factory specifications replicating the original in design and fitment. This bumper was used for various applications...
Hex Head Sems Screw; With Washer; A/AB Point; 6.3-1.81 x 25mm; Black Phosphate; Each
Reproduction black phosphate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 6.3-1.81 x 25mm...
1962-1982 GM; Carburetor, Door, Tailgate; Spring Steel Rod Clip; RH Passenger Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
5/16-18 X 9/16" Self-Tapping Bolt. Brake and fuel line bolts with correct Anchor head marking. Self tapping, non pointed 1/2" bolt. Set of 6. {fitment}