Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1970-81 Camaro, Firebird, Nova; "Bullet" Remote Outer Door Mirror; LH Drivers Side
Reproduction of the original remote outer door mirror designed for use on a variety of 1970-81 GM models including Camaro, Firebird, Nova, LeMans, GTO, Cutless, 442, and more. Manufactured with a die-cast zinc outer body...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Reproduction of the original convertible top piston lower bolt bushing designed for use with varius 1967-72 Buick, Chevrolet, Pontiac, Oldsmobile convertible models as listed. This bushing mounts from the rear control link of...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a set of 10, refer to part...
Bumper Bolt with Stainless Steel Head; Zinc Plated; 7 /16"-14 x 1" Bolt with Hex Nut
Reproduction bumper bolt with hex nut manufactured in zinc plated material offering an authentic appearance and fitment. Measures 7/16" -14 x 1" and features a stainless steel cap. Head diameter 31/32". Each bolt will replace...
1970-2002 GM; Hood Insulation Fastener; Each
Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...