OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
1969-70 Mustang; Front Door Post Seals; Pair
Reproduction of the original front of door rubber seals manufactured with correct hard rubber material. These seals are located above the door hinge near the top area. Includes correct molded seals and 4 mounting screws. Sold...
1969-70 Mustang; Glass Run Weatherstrip Bracket; Hinge Side; LH
Reproduction of the original glass run weatherstrip metal guide channel for use with 1969-70 Mustang and Cougar models. This channel mounts vertically inside of door to attach the horizontal glass run weatherstrip. Used at...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
1965-70 Ford Mustang Coupe or Convertible; Luggage Compartment Weatherstrip; Trunk Lid Seal
High quality reproduction trunk lid weatherstrip for 1965-70 Mustang coupe and convertible models. Each weatherstrip is manufactured in quality EPDM rubber replicating the original configuration. Some trimming may be required...
1969-71 Ford Mustang; Shaker Hood Scoop Seal and Plate; with Drain Hose
This seal installs between the air cleaner and Shaker hood scoop. When the hood is closed, it seals the opening where the Shaker scoop passes through the hood, and directs water away from the air cleaner and engine with a...
1969-70 Ford Mustang; Door Frame Weatherstrips
High quality reproductions of the door weatherstrip pieces that are glued around the front, back, and lower edges of the doors. Sold in pairs. Fits 1969 - 1970 Mustang.Made in USADon't forget to order our 3M8008...
1969-70 Mustang; Glass Run Weatherstrip Bracket; Hinge Side; RH
Reproduction of the original glass run weatherstrip metal guide channel for use with 1969-70 Mustang and Cougar models. This channel mounts vertically inside of door to attach the horizontal glass run weatherstrip. Used at...
1969-70 Ford Mustang; Hood Side Rubber Bumper Set; Push In Hood Bumper On Fender; Set of 4
Reproduction hood rubber bumpers that install on 1969-70 Mustang. The rubber hood bumpers can wear out, deteriorate, or simply get lost. These reproduction rubber bumpers will allow the hood to be adjusted and aligned while...
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1964-73 Ford/Mercury; Fuel Tank Filler Pipe Neck To Body Gasket
Reproduction of the original gas tank filler neck gasket for 1964-73 Mustang and 1967-68 Cougar models. The fuel tank-to-body gasket will ensure a leak free seal between your filler neck and gas tank. Replaces OE # C5ZZ-9076....
Sealstrip Glass Setting Tape; 10 Foot Roll; 1/32" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
Sealstrip Glass Setting Tape 10 Foot Roll; 1/16" Tape Thickness; for Door, Vent, Quarter Glass
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
Sealstrip Glass Setting Tape ; 10 Foot Roll ; 3/64" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...