Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1948-86 Ford; Fuel Tank Sending Unit Brass Float; Various Models
Reproduction of the original style and correct brass float for use with various 1948-86 Ford and Mercury models as listed below. This sending unit brass float is desirable for its long-lasting dependability as it lasts much...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1967-70 Ford Mustang; Rubber Filler Neck Hose; Fuel Tank to Filler Pipe; 4-7/8" Long; 2-3/16" id
Reproduction fuel filler hose that seals the inlet filler neck to the fuel tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...
1965-73 Ford Mustang; Screw Set; Gas Tank Mounting; 13 Piece Set
This 13 piece set contains all the mounting hardware needed to install your gas fuel tank. Each piece is factory correct. Screws and bolts are all fabricated from heavy-duty steel and coated to prevent any corrosion. Ford...
1964-70 Ford/Mercury; Wire Clamps; For Fuel Filler Neck Hose
Reproduction wire-style fuel tank filler neck clamps for 1964-70 Mustang, 1967-70 Cougar and 1966-70 Fairlane models. If your hose is loose, the filler neck clamps could be worn out and require replacing. These clamps are...
1970 Mustang, Cougar; Fuel Tank Sending Unit; 3/8" Inlet; without Low Fuel Warning
Reproduction of the most accurate reproduction fuel tank sending unit in the industry. Features the original design including a filter, O-ring, and brass float that replicate the original in appearance and functionality. This...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
1970 Ford Mustang; Fuel Tank Filler Neck Pipe Assembly
Reproduction filler pipe for 1970 Mustang models. Each fuel tank filler neck is manufactured to OE specifications replicating the original in quality, design, and fitment. will mount to your Mustang tail light panel and...
1960-97 Ford, Mercury; Fuel Tank Sending Unit O-Ring; Various Models
Our synthetic rubber fuel sending unit oring gasket seal is produced to be resistant to heat, oil and chemicals. Features superb elasticity and bonding capabilities to ensure that it will not lose its shape over time. Will...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1964-73 Ford/Mercury; Fuel Tank Filler Pipe Neck To Body Gasket
Reproduction of the original gas tank filler neck gasket for 1964-73 Mustang and 1967-68 Cougar models. The fuel tank-to-body gasket will ensure a leak free seal between your filler neck and gas tank. Replaces OE # C5ZZ-9076....
1970-73 Ford Mustang; Hex Head Screw Set; For Fuel Filler Neck; 5 Piece Set
Reproduction fuel filler neck screw kit. Each 5 piece screw kit includes the hex head screws that are required to mount the fuel filler neck to the tail lamp panel on 1964-69 Mustang models. Ford Applications: 1970-73 Ford...
Hex Head Sems Screw; With Washer; A/AB Point; 6.3-1.81 x 25mm; Black Phosphate; Each
Reproduction black phosphate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 6.3-1.81 x 25mm...