Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
1970 Dodge Challenger; Fuel Tank; without Vent Tubes; Stainless Steel; 18 Gallon Capacity
Correct reproduction of the original fuel tank designed for with 1970 Dodge Challenger models. This reproduction fuel tank is manufactured in stainless steel offering a beautiful appearance and long last durability. This is a...
1970-75 Dodge, Plymouth A, B, E Body; Fuel Tank Filler Neck Grommet
Reproduction fuel tank to filler neck rubber grommet to replace the old or worn out original. Replace brittle or deteriorated fuel tank filler neck grommets with this quality reproduction grommet to eliminate vapor or fuel...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Reproduction of the original fuel tank designed for use with 1968-70 Dodge and Plymouth Coronet, Belvedere, GTX, Road Runner, and Satellite models. This is a 19-gallon fuel tank with two vent pipes on the front of the tank....
1970 Charger With EEC 19 Gallon Fuel Tank - Niterne Coated Steel (4 Side Vent Tubes)
Replacement fuel tank for 1970 Charger models. These are manufactured in niterne plated steel (as original) and designed to fit like factory-installed. Includes four vent tubes on left side of tank. Includes lock ring and...
Reproduction of the original fuel tank designed for use with 1968-70 Dodge Charger models without EEC. This fuel tank is manufactured in plated steel featuring a niterne coating same as original. Designed to replicate the...
1960-1976 Chrysler, Dodge, Plymouth; Fuel Tank Mounting Studs ; Pair; OER
Reproduction of the original style fuel tank mounting studs designed for use on various 1960-1976 Mopar models. Fuel tank mounting studs, also known as J-bolts, are required when replacing your fuel tank straps. Manufactured...
Correct reproduction of the original fuel tank designed for with 1968-70 Dodge Coronet, and Plymouth Belvedere, GTX, Road Runner, and Satellite models. This reproduction fuel tank is manufactured in stamped steel featuring a...
1968-70 Dodge Charger; Zinc Coated; Fuel Tank; w/o EEC; 19 Gallon; No Vent Tubes
Reproduction of the original fuel tank designed for use with 1968-70 Dodge Charger models without EEC. This fuel tank is manufactured in plated steel featuring a zinc coating same as original. Designed to replicate the...
Reproduction of the original fuel tank designed for use with 1968-1970 Dodge Dart, and Plymouth Barracuda, Valiant models without EEC (evaporative emission control). This reproduction fuel tank is manufactured in quality...
1970 Dodge Challenger; NiTerne Coated Fuel Tank; w/o Vent Tubes; 18 Gallon Capacity
Correct reproduction of the original fuel tank designed for with 1970 Dodge Challenger models. This reproduction fuel tank is manufactured in stamped steel featuring an original style NiTerne coating for superior rust and...
Correct reproduction of the original fuel tank designed for with 1970 Dodge Coronet, Super Bee, Plymouth Belvedere, GTX, Road Runner, and Satellite models. This reproduction fuel tank is manufactured in stamped steel...
1962-76 Dodge, Plymouth; Fuel Sending Unit Ground Strap; 3-3/4" Steel
Reproduction of the original fuel tank sending unit ground strap designed for use with most 1962-76 Dodge and Plymouth A-body, B-body and E-body models. Attaches near the short fuel hose that joins the fuel tank sender line...
1969-70 Charger, 1969 Barracuda; Quick-Fill Fuel Cap; with "Fuel" wording
Reproduction "Quick-Fill" fuel cap for 1969-70 Charger and 1969 Plymouth Barracuda models. Manufactured using factory specifications with great attention to detail, these vented replacement fuel caps offer a 'like-factory'...
1970-1971 Dart, Valiant, Swinger, Duster, Demon; Fuel Tank; Zinc Coated; with EEC;16 Gallon Capacity
Correct reproduction of the original fuel tank designed for with 1970-1971 Dodge Dart, Valiant, Swinger, Duster, Demon models with EEC (evaporative emission control). This reproduction fuel tank is manufactured in stamped...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1968-70 Charger, Coronet, GTX, Road Runner, Belvedere; Fuel Tank Sending Unit; 5/16" Outlet
After years of use, your fuel sending unit can wear out or stop working. When that happens, it can cause significant issues for the fuel gauge. Ensure that you always know how much fuel you actually have by replacing your...
1970-74 Dodge, Plymouth E-Body; Standard Fuel Tank Sending Unit; 5/16" Outlet
After years of use, your fuel sending unit can wear out or stop working. When that happens, it can cause significant issues for the fuel gauge. Ensure that you always know how much fuel you actually have by replacing your...
1962-76 Dodge, Plymouth A, B, E Body; Fuel Sending Unit Rubber Seal; 2-1/4" ID
Reproduction of the original rubber fuel sending unit seal designed for use with 1962-76 Dodge and Plymouth A, B, and E Body models. Replaces original Mopar part number # 1948757. We suggest replacing this seal every few...
1967-76 Dart, Barracuda, Valiant, Duster; Vented Fuel Cap
Reproduction of the original fuel cap designed for use with 1967-76 Dodge Dart and Plymouth Barracuda, Valiant, Duster, Scamp, and Swinger models. Each cap is manufactured to factory specifications featuring a primer coating...
1967-71 Dart, Barracuda, Valiant; Chrome Fuel Cap; Non Vented
Reproduction fuel cap for 1967-71 Dodge & Plymouth A-Body models. Each cap is manufactured to correct factory specifications replicating the original in design, appearance, and fitment. This is a non-vented cap features a...
1968-70 Dodge, Plymouth B-Body; Fuel Sending Unit; 3/8" Outlet; 1/4" Return Line; Stainless Steel
Reproduction of the original fuel sending unit designed for use with 1968-1970 Dodge and Plymouth B-Body models. After years of use, your fuel sending unit can wear out or stop working entirely. When that happens, it can...
1968-70 Dodge Charger; Fuel Tank Filler Neck Seal
Reproduction fuel filler neck to trunk floor seal for 1968-70 Charger models. Designed to keep out fumes and road debris, this seal attaches to the inside of the trunk floor and the fuel filler neck passes thru it....
1970 Dodge Challenger; Fuel Tank Filler Neck
Reproduction gas tank filler neck for 1970 Dodge Challenger models. This zinc coated filler neck is manufactured to replace the original exactly. Features OE configuration and comes zinc coated for long lasting dependability....
1968-70 Dodge, Plymouth B-Body; Fuel Sending Unit; 5/16" Single Outlet; Stainless Steel
Reproduction of the original fuel sending unit designed for use with 1968-70 Dodge and Plymouth B-Body models. After years of use, your fuel sending unit can wear out or stop working entirely. When that happens, it can cause...
1968-70 Dodge, Plymouth B-Body; Fuel Sending Unit; 1/2" Outlet, 1/4" Fuel Return; Stainless Steel
Reproduction of the original fuel sending unit designed for use with 1968-1970 Dodge and Plymouth B-Body models. After years of use, your fuel sending unit can wear out or stop working entirely. When that happens, it can...
1970-74 E-Body Fuel Tank Mounting Straps ; Stainless Steel; with Hardware
Reproduction of the original fuel tank mounting straps designed and manufactured from long lasting stainless steel material for long lasting dependability. For use on 1970-74 E-Body models. Approximate strap measurement bend...
1968-76 Dodge, Plymouth A Body; Fuel Tank Mounting Straps; Stainless Steel; Pair
Reproduction of the original style fuel tank mounting straps designed for use with 1968-76 Dodge and Plymouth A-Body models as listed below. Each strap is manufactured in quality stainless steel to original factory dimensions...
Reproduction of the original fuel tank mounting strap designed for use with 1968-1976 Dodge Dart, Dart Sport Plymouth Duster, Demon, Twister, Swinger, Barracuda, and Valiant models. Each strap is manufactured in quality...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1964-74 Dodge, Plymouth; Fuel Tank Filler Neck Grommet; Various Models
Reproduction fuel filler neck grommet for various 1964-74 Dodge & Plymouth models. Eliminate vapor or fuel leaks by replacing the fuel filler neck grommet. Manufactured from OE materials for long lasting fit and funcionality....
Correct reproduction of the original fuel tank designed for with 1968-1970 Dart, Barracuda, Valiant, and Swinger models. This reproduction fuel tank is manufactured in stainless steel replicating the original Mopar tank...
Correct reproduction of the original fuel tank designed for with 1968-1970 Coronet, Satellite, Belvedere, GTX, Road Runner models. This reproduction fuel tank is manufactured in stainless steel replicating the original GM...
Correct reproduction of the original fuel tank designed for with 1968-1970 Charger models without EEC. This reproduction fuel tank is manufactured in stainless steel replicating the original GM tank offering originality with...
Reproduction of the original fuel tank designed for use with 1970-1971 Dodge Dart, Plymouth Barracuda, Valiant models with EEC (evaporative emission control). This reproduction fuel tank is manufactured in quality stamped...
1970 Dodge Coronet, Plymouth B-Body; 19 Gallon Fuel Tank; 4 Side Vent Tubes; Niterne Steel; CR9D
This is a high quality replacement fuel tank for 1970 Dodge and Plymouth B-Body models except Charger. These are manufactured in authentic Ni-Terne coated steel (as original) and designed to look and fit like the originals....
Reproduction of the original accelerator pedal pad designed for use on 1966-70 Belvedere, Charger, Road Runner, Satellite and Superbird B-Body models. This quality reproduction is manufactured in hard rubber material...
1970 Dodge Charger; Zinc Coated Fuel Tank; w/ EEC; 4 Side Vent Tubes; 19 Gallon Capacity
Correct reproduction of the original fuel tank designed for with 1970 Dodge Charger models with EEC (evaporative emission control). This reproduction fuel tank is manufactured in stamped steel featuring a Zinc coating for...
Correct reproduction of the original fuel tank designed for with 1968-1970 Dodge Dart, Plymouth Barracuda, Valiant models. This reproduction fuel tank is manufactured in stamped steel featuring a heavy Zinc coating for rust...
1970 Dodge Challenger; Fuel Tank; w/o Vent Tubes; Zinc Coated; 18 Gallon Capacity
Correct reproduction of the original fuel tank designed for with 1970 Dodge Challenger models. This reproduction fuel tank is manufactured in stamped steel featuring a Zinc coating for rust and corrosion prevention. This is a...
1970-74 Challenger R/T Quick-Fill Fuel Cap with Trim Ring
Replacement "Quick-Fill" style fuel cap for 1970-71 Challenger R/T models. Manufactured using factory specifications with great attention to detail, these replacement fuel caps offer a factory-like appearance. Also known as...
1968-70 Coronet, GTX, Road Runner, Satellite; Fuel Tank Filler Neck
Reproduction of the original fuel tank filler neck designed for use with 1968-70 Dodge Coronet, Super Bee, 440, 500, R/T, and Plymouth Belvedere, GTX, Road Runner, Satellite, and Superbird models. Each filler neck is...
1970-74 Dodge Challenger; Quick-Fill Fuel Cap; with "Fuel" wording
Replacement "Quick-Fill" style fuel cap for 1970-71 Challenger R/T models. Manufactured using factory specifications with great attention to detail, these replacement fuel caps offer a 'like-factory' appearance. Also known as...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1968-70 Dodge, Plymouth B-Body; Fuel Tank Sending Unit ; with 3/8" Outlet, 1/4" Return Line
After years of use, your fuel sending unit can wear out or stop working. When that happens, it can cause significant issues for the fuel gauge. Ensure that you always know how much fuel you actually have by replacing your...
1968-70 Dodge Charger, 1967-68 Barracuda, 1967 GTX ; Quick-Fill Fuel Cap Trim Ring
Reproduction "Quick-Fill" or "Flip Top" fuel cap trim ring for 1968-70 Dodge Charger, 1967-68 Plymouth Barracuda, and 1967 GTX models. Each fuel cap trim ring is manufactured in die-cast zinc featuring a polished chrome...
1963-76 Dodge, Plymouth; A-Body; Fuel Tank Sending Unit ; 5/16" Outlet
After years of use, your fuel sending unit can wear out or stop working which can cause significant issues with your fuel gauge. Ensure you always know how much fuel you actually have in the tank by replacing your worn out...
1970-74 Barracuda, Cuda, Challenger; Fuel Tank Filler Neck Seal
Reproduction fuel filler neck to trunk floor seals for 1970-74 E-Body models. Designed to keep out fumes and road debris, each seal attaches to the inside of the trunk floor and surrounds fuel filler neck. Manufactured in...
1970-74 Dodge, Plymouth E-Body; Standard Fuel Tank Sending Unit; with 3/8" Outlet ; 1/4" Return Line
After years of use, your fuel sending unit can wear out or stop working. When that happens, it can cause significant issues for the fuel gauge. Ensure that you always know how much fuel you actually have by replacing your...
1963-76 Dodge, Plymouth A-Body; Fuel Tank Sending Unit; 3/8" Outlet with 1/4" Fuel Return
After years of use, your fuel sending unit can wear out or stop working entirely. When that happens, it can cause your fuel gauge not to work or even send incorrect readings to the fuel gauge. Ensure that you always know how...
1968-71 Dodge Plymouth; Fuel Filter, Vapor Separator; with 426, 440
Help prevent vapor lock the way the factory intended by installing the correct fuel filter/vapor separator on your 426 Hemi or 440 ci equipped vehicle. This part mounts near the fuel pump and is designed to filter the fuel...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...