Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1968-72 Outer Door Mirror; Chrome: LH; Smooth Style Base; Various GM Models
Reproduction of the original outer door mirror designed for use on various 1968-72 GM models. Each mirror is manufactured in quality die-cast zinc replicating the original mirror in quality and fit. This reproduction mirror...
1955-82 Spare Tire Hold Down Nut; 5/16"-18 Thread; 3.88" Wide; Zinc Finish
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1968-79 Camaro, Chevelle, Impala, Nova, Ventura; Rear License Plate Bracket; with Hinge; EDP Coated
Reproduction rear license plate bracket designed for various 1968-79 GM models. This authentic OE-style bracket is manufactured from quality stamped steel and includes a spring-loaded hinged door that allows access to the...
1969-87 GM; Door Hinge Repair Set ; Except with 15mm OD Bushings
Reproduction of the original door hinge components for use on various GM models. Repair the broken door hinges with this comprehensive repair set. Each repair kit includes 4 properly hardened shoulder pivot pins and 8...
1969-70 Caprice / Impala Custom 2 Door Hardtop Clear Back Glass
Replacing your original damaged or missing back glass will enhance your vehicle's appearance and safety by allowing you to see clearly. Don't settle for anything less than original quality glass when replacing the windows of...
Replacing your original damaged or missing back glass will enhance your vehicle's appearance and safety by allowing you to see clearly. Don't settle for anything less than original quality glass when replacing the windows of...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
Reproduction of the original front windshield glass for use with 1969-70 Buick, Chevy, Pontiac, Oldsmobile Full Size models as listed. This windshield is manufactured with tempered laminate safety glass that meets the...
Reproduction of the original convertible top cylinder designed for use with 1965-1970 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile full size convertible models. Each cylinder is manufactured from a solid aluminum...
1970-75 Camaro, Firebird, Impala; Outer Door Handle; Die-Cast Chrome; Passenger Side
Reproduction of the original outer door handle designed for use with various 1970-75 GM vehicles including Camaro, Firebird, Impala, and various other models. Each outer door handle is manufactured to factory specifications...
Reproduction of the original front windshield glass for use with 1969-70 Buick, Chevy, Pontiac, Oldsmobile Full Size models as listed. This windshield is manufactured with tempered laminate safety glass that meets the...
Wiper Blade Insert; Replacement; 16" Anco Style; Each
OER reproduction Anco-style windshield wiper blade insert for various classic American vehicle models from the 1960's and up. These 16" wiper blades are manufactured from quality molded rubber as original. Refill is...
