Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for various GM models. This spacer is manufactured from durable EPDM rubber. This spacer was used to correct the ride height on vehicles that did not sit level...
1969-70 Impala, Bel Air, Biscayne, Caprice; Front End Suspension Rebuild Kit
1969-70 Chevrolet Impala front end rebuild kit providing nearly everything required to restore a worn out suspension system to smooth, reliable performance. This comprehensive kit includes the essential components needed to...
1965-70 Impala, Caprice, Bel Air; Upper Tubular Control Arms; RH & LH; Pair
These tubular upper control arms are engineered for maximum strength, durability, and visual impact. Designed as direct stock replacements, they provide a clean, upgraded appearance while offering significantly improved...
Reproduction molded rubber front coil spring insulator that mounts between the coil spring and the frame on various 1949-96 vehicles. This insulator keeps the spring from riding metal-to-metal on the frame. Coil spring...
1955-70 Full Size Chevy; Upper Ball Joint; with Hardware; RH or LH
Reproduction of the original upper ball joint designed for use with 1955-70 Chevy full size models including 1955-57 Chevy, and 1958-70 Impala, Bel Air, Biscayne, and Caprice models. Control arm ball joints take a beating...
1965-70 Impala, Caprice, Bel Air; Lower Tubular Control Arms; RH & LH; Pair
These tubular upper control arms are engineered for maximum strength, durability, and visual impact. Designed as direct stock replacements, they offer a clean upgraded appearance along with significantly improved rigidity...
1958-82 Chevrolet; Lower Ball Joint with Hardware; Various Applications
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
1974-78 Mustang II; Front Sway Bar Kit; 3/4" ; 43-1/4" Wide; for Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks equipped with standard width crossmember Mustang II front suspension systems. This sway bar is engineered to reduce body roll, under steer, and over steer during...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4? to 4? inclusive. These heat treated washers are for general purpose and structural use. For use...
1967-70 Impala/Full Size Passenger Car; Center Link
Reproduction drag link/center link for 1967-70 Chevrolet Impala/full size models as listed. Includes hardware. Full ball stud pitman arm end, greaseable, self aligning no bind design, low friction, and ready to install....
1961-75 Buick, Chevy, Olds, Pontiac; Upper Control Arm Bumper; Each
Quality reproduction of the original upper control arm bumper designed for use with various 1967-75 General Motors models. Each bumper is manufactured in heavy duty EPDM molded rubber material to original specifications...
1959-70 Impala, Bel Air, Biscayne, Caprice; Trailing Arm Bushing; Each
Rear trailing arm bushing for various 1959-1970 GM full size models including Impala, Bel Air, Caprice, and Biscayne. This high quality reproduction bushing is engineered to replace the worn or deteriorated original,...
1965-70 Impala, Bel Air, Biscayne, Caprice; Lower Control Arm Bushing; Front; Each
Superb reproduction of the original control arm bushing reproduced to factory specifications. Add new life to your suspension by replacing the old bushings with these quality reproductions. Sold individually. 2 required per...
1955-74 Buick, Chevy, Olds, Pontiac; Upper Control Arm Bushing; Each; Various Models
1958-1970 Chevrolet Biscayne 1958-1970 Chevrolet Bel Air 1966-1970 Chevrolet Caprice 1970-1972 Chevrolet Monte Carlo 1968-1968 Chevrolet Chevy II 1968-1974 Chevrolet Nova 1955-1957 Chevrolet Bel Air 1955-1957 Chevrolet One...
1962-70 Buick, Chevy; Pontiac, Oldsmobile; Control Arm Bumper; Rubber; Each; Various Models
Reproduction of the original control arm bumper designed for use on various GM models. Each bumper is manufactured to factory specifications in the correct configuration and includes a built in stud ensuring a perfect fit....
1965-70 Impala, Bel Air, Biscayne; Tubular Control Arm Set; Black;
Tubular control arms are engineered for maximum strength, durability, and visual impact. Designed as direct stock replacements, these upper control arms provide a cleaner appearance and significantly increased rigidity over...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...