1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van ...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
1967-02 Accelerator Pedal Tension Spring
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1967-81 GM; Accelerator Pedal Pad Trim Plate; Stainless; Various Models
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
1967-02 Accelerator Pedal Mounting Pin
This special mounting pin is just what you need to correct a loose accelerator pad. This special design allows the pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems commonly...
1955-69 Accelerator Pedal Firewall Bushings ; Pair
OER® reproduction of the original accelerator firewall bushings designed for use on various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive...
1969 Firebird; Pedal Pad Kit; with Stainless Trim; Auto Trans; 6 Piece Set
Reproduction of the original pedal pads with trim designed for 1969 Firebird models. This pedal pad and trim set is designed to replace the worn out original pads for 1969 Firebird models with automatic transmissions....
1968-74 Accelerator Pedal Pad To Rod Support
Reproduction of the original accelerator pedal rod support for use on the various applications listed. Each support is manufactured in injection molded ABS offering an exact replacement of the original. Applications: ...
1969-71 GM Pedal Pad Kit Manual Transmission; With Disc Brakes Emblem - 8 Piece
Reproduction of the original pedal pads designed for 1969-71 Camaro and 1970-71 Firebird models equipped with 3" brake and clutch pedal. Each pad is manufactured to original factory specs! 8 piece set includes the 3" brake...
Powerglide Upper Kickdown Clip
OER® Authorized reproduction upper kickdown clip for models with powerglide automatic transmission. Connects the upper passing gear kickdown rod to the bellcrank assembly. Applications: 1967-69 Camaro with...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...
1969 Firebird; Pedal Pad Kit; Manual Trans; 8 Piece Set
Reproduction of the original pedal pads designed for 1969 Firebird models. This pedal pad set is designed to replace the worn out original pads for 1969 Firebird models with manual transmission. Replacing the pedal pads will...