OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
1969-70 Mustang; Front Door Post Seals; Pair
Reproduction of the original front of door rubber seals manufactured with correct hard rubber material. These seals are located above the door hinge near the top area. Includes correct molded seals and 4 mounting screws. Sold...
1967-72 Ford F100, F250, F350 Pickup Truck; Door Body Weatherstrip Seals; RH and LH; Pair
Reproduction door seal weatherstrip set for 1967-72 Ford F100, F250, F350 pickup truck models. These high-quality, ozone-resistant EPDM rubber gaskets mount on the body of the truck with weatherstrip adhesive sealing the cab...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
1965-70 Ford Mustang Coupe or Convertible; Luggage Compartment Weatherstrip; Trunk Lid Seal
High quality reproduction trunk lid weatherstrip for 1965-70 Mustang coupe and convertible models. Each weatherstrip is manufactured in quality EPDM rubber replicating the original configuration. Some trimming may be required...
1969-71 Ford Mustang; Shaker Hood Scoop Seal and Plate; with Drain Hose
This seal installs between the air cleaner and Shaker hood scoop. When the hood is closed, it seals the opening where the Shaker scoop passes through the hood, and directs water away from the air cleaner and engine with a...
1973-79 Ford Truck/Bronco; Firewall To Hood Seal; Cowl Lacing
Reproduction cowl to hood seal for 1973-79 Ford F-100, F-250, and F-350 trucks and 1978-79 Broncos. This gasket installs on the top of the cowl providing a seal between the firewall and the hood. It is made from ozone...
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
Sealstrip Glass Setting Tape; 10 Foot Roll; 1/32" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
1966-77 Ford Bronco; Door Window Lower Division Bar Set; LH and RH
Reproduction door window lower division bar set for 1966-77 Ford Bronco. Manufactured in stamped steel to factory original configuration. Supplied as a set of 4 pieces that includes the LH and RH sides. {fitment}
Door, Vent, Quarter Glass; Sealstrip Glass Setting Tape;10 Foot Roll; 1/16" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
Sealstrip Glass Setting Tape ; 10 Foot Roll ; 3/64" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1967-69 Camaro, Firebird; Plastic Clip Set; Radiator Support To Hood Seal; 9 Piece Set
Reproduction of the radiator support to hood seal clip set designed for 1967-69 Camaro and Firebird models with air conditioning. Each clip is injection molded to original specifications. Clips are designed to hold the hood...
1941-76 Mohair Window Channel Liner ; 2-5/8" wide x 8" long
When it comes to relining the door and quarter window channels, this Mohair liner material is what you'll need. A finely textured mohair lining material with a rubberized backing. Inside the door, there are "U" shaped...