1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models
1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
1969 Camaro, Firebird; Fuel Tank; with Fuel Neck; Stainless Steel; 18 Gallon Capacity
Correct reproduction of the original fuel tank designed for with 1969 Camaro and Firebird models. This reproduction fuel tank is manufactured in stainless steel replicating the original GM tank offering originality with an...
1967-72 Camaro, Nova, Firebird; Fuel Tank Sending Unit; 3/8"; with 1/4" Vent
Reproduction of the original fuel tank sending unit designed for use with 1967-68 Chevrolet Camaro and Firebird models with 3/8" line and 1/4" vent. After years of use, your fuel sending unit can stop working properly. When...
1967-69 Camaro, Firebird, 1967-72 Nova; Carburetor to Accelerator Cable; 6 Cylinder; OER
Reproduction accelerator cable for 1967 Camaro, Firebird (6 and 8 cyl), 1968-69 Camaro, Firebird (6 cyl), 1968-72 Nova (6 cyl) models. A faulty cable can lead to problems associated with acceleration and become a safety...
1967-69 Camaro, Firebird; Fuel Tank Mounting Straps; Black EDP Coated; Pair
Reproduction fuel tank mounting straps designed for use with all 1967-69 Camaro and Firebird models. These OE-style straps are built to factory specifications and crafted from heavy-duty stamped steel for long-lasting...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1969 Camaro / Firebird Fuel Tank Kit with 18 Gallon Zinc-Coated Tank
Replace all the necessary components for your 1969 Camaro or Firebird with OER® fuel tank kit. Each kit provides the individual components needed to replace you leaking or damaged fuel tank. Kit includes: Zin c-Coated...
1967-69 Camaro; Accelerator Pedal Assembly; with 6 Cyl. or Cross Ram Dual Carburators with 8 Cyl
Reproduction of the original accelerator assembly designed for use with 6 cylinder or 8 cylinder dual carburetor Cross Ram models. Extends from the firewall and comes with the accelerator pedal, pedal mount pin and spring,...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1969 Camaro; Accelerator Pedal Pad Assembly; V8; with Cowl Induction
This is the complete accelerator pedal assembly which extends from the firewall on all V8-equipped vehicles with cowl induction. This assembly comes complete with the accelerator pedal, pedal mount pin and spring, accelerator...
1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl
Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1969 Chevrolet Camaro; Accelerator Throttle Arm; V8; with Cowl Induction Hood
Reproduction of the original accelerator throttle arm designed for use with 1969 Chevrolet Camaro models that included a cowl induction hood. This is a correct reproduction of the original GM throttle lever arm. Manufactured...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1968-72 Camaro, Impala, Nova; Holley Throttle Cable Bracket
Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1968-70 Camaro, Firebird, Nova, Impala; Fuel Tank Vent Valve
Reproduction of the original gas tank vent valve that's installed on various 1968-70 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured in injection molded plastic to factory specifications. This commonly damaged...
1968-69 Camaro, Nova; Accelerator Throttle Arm V8; 307ci, 350ci, 396ci; w/o Cowl Induction
Reproduction of the original throttle arm designed for use on 1968-69 Camaro and Nova models. Each throttle arm is produced to replicate the original in quality and fit. Replace your worn out or damaged original throttle arm...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Reduce heat coming off of the intake with this reproduction carburetor base gasket with heat shield, installs between the carburetor and intake manifold. This gasket and shield was original equipment for most 1970 Chevrolet...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1967-72 Camaro, Firbeird, Nova; Fuel Tank Strap Mounting Bolt Kit ; 10 Piece Set ; Various Models
Reproduction of the original mounting bolts and hardware designed to install fuel tank mounting straps on various GM models. It's easy to replace the fuel tank straps when you have the right hardware. This set includes the...
1967-69 Camaro, Firebird,1968-72 Nova; Fuel Tank Sending Unit; with 3/8" Single Line
Reproduction fuel tank sending unit for 1967-69 Camaro and Firebird models, and 1968-72 Nova models with 3/8" line. After years of use, your fuel sending unit can wear out or stop working. When that happens, it can cause your...
1969 Camaro / Firebird Fuel Tank Kit with 18 Gallon Stainless Steel Tank
Replace all the necessary components for your 1969 Camaro or Firebird with OER® fuel tank kit. Each kit provides the individual components needed to replace you leaking or damaged fuel tank. Kit includes: Sta inless Steel...
1969 Camaro, Firebird; Fuel Tank; with Neck; 18 Gallon; Zinc Coated Steel
Reproduction fuel tank for 1969 Camaro and Firebird models. This reproduction fuel tank is manufactured in zinc coated steel and includes the fuel sender lock-ring and o-ring gasket for a complete installation. This is a 18...
1969 Camaro, Firebird; Ni-terne Coated Fuel Tank; with Fuel Neck; 18 Gallon
Correct reproduction of the original fuel tank designed for with 1969 Camaro and Firebird models. This reproduction fuel tank is manufactured in original style Nitern coated steel and includes the fuel sender lock-ring and...
Reproduction clips used to mount the fuel line to the frame. Includes six 3/8" clips. Applications: 1967-69 Chevrolet Camaro - Big Block 1967-69 Chevrolet Camaro - Small Block w/4bbl 1965-86 Chevrolet/GMC Truck 1965-70...
1965-74 Holley; Carburetor Heat Shield; 4 Barrel with 396,454 Engine
OER® reproduction carburetor heat shield for all GM models with a Holley 4 bbl carburetor. This heat shield will help cool the intake charge for better performance. Original for 1970 396ci & 454ci with Special...
Reproduction of the complete accelerator pedal assembly which extends from the firewall on all V8-equipped 1967 Firebird models. This accelerator pedal assembly comes complete with the pedal, pedal mount pin and spring,...
1968-69 327, 350 Carb to Accelerator Lever Rod; Small Block with 4 bbl Carb
Reproduction 1968-69 accelerator pedal rod for 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1967-69 Camaro/Firebird; Fuel Tank Straps; Stainless Steel
Reproduction fuel tank mounting straps that fit all 1967-69 Camaro & Firebird models.These quality straps are manufactured in heavy duty pre-formed stainless steel that offers a uniquely custom appearance that replicates the...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1968-69 Camaro, Firebird; 1968-72 Nova; Fuel Tank Sending Unit; Single Line; 5/16"
Reproduction of the original fuel tank sending unit designed for use with 1968-69 Camaro and Firebird models, and 1968-72 Nova models with 5/16" line. After years of use, your fuel sending unit can wear out or stop working....
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1968-69 Camaro; Crossram Throttle Rod; Accelerator Pedal Rod
Reproduction crossram throttle rod or accelerator pedal rod for 1968-69 Camaro models equipped with the optional Crossram induction system. This unique linkage rod mounts to the accelerator pedal at the firewall and attaches...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
1967-69 Camaro, 1970 Nova; Accelerator Pedal Rod; V8
Reproduction of the original accelerator pedal pad rod designed for use on 1967 Camaro (6 & 8 cylinder), 1968-69 Camaro (8 cylinder), and 1970 Chevy II Nova models. This rod connects between the throttle arm and the...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1962-81 GM; Fuel Tank Sending Unit Lock Ring; Small; 1-15/16"; Various Models
Correct reproduction fuel tank sending unit locking ring which secures the fuel tank sending unit to the gas tank. Replaces the original ring which are commonly destroyed when being removed. This ring helps to seal the...
This special mounting pin is just what you need to correct a loose accelerator pad. This OEM design allows the accelerator pad to attach to the accelerator arm correctly and tightly. Replacing this pin will fix the problems...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1969-81 Fuel and Brake Line Clip ; Dual Line 3/8" and 1/4"
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1968-81 GM Pedal Pad and Trim Plate Kit; Auto Trans; 6 Piece Kit; Various Models
Reproduction of the original pedal pads and pedal pad trim plates to fit various GM models. This pedal pad set is designed to replace the worn out original pads for models equipped with automatic transmission. Replacing the...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
Fuel Sending Unit Filter Strainer; For 5/16" Pickup Tube
Correct OER® reproduction of the original fuel tank float strainer designed for use with various 1942-85 GM, Chrysler, Dodge, Plymouth models as listed below. This filter will keep dirt and other elements from clogging or...
1968-74 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Pad to Rod Support
Reproduction of the original style GM accelerator pedal rod support for use on the various Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. Each support is manufactured in injection molded ABS offering an exact...
Fuel and Brake Line Clip Set ; Dual Line 3/8" and 1/4" ; 7 Piece Set
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1968-79 Accelerator Control Cable Retainer ; Various Models
OER® reproduction of the correct cable retainer used to hold the accelerator control cable. This retainer slips over the cable and clips into the hole on the accelerator pedal arm. Manufactured in injection molded plastic...