1968-69 Camaro SS; Hood Louver Set; with Hardware; Pair; "Show Quality"
Reproduction of the original die-cast hood louvers designed for use with all 1968-69 Camaro Super Sport models equipped with a 350 or 396 engine. Manufactured with OER® exclusive tooling to exact factory specifications....
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1965-69 Impala, Camaro, Nova, Firebird; Hood Hinge; LH; Driver Side
Reproduction of the original hood hinge assembly designed for various GM models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the hood spring when installing a new...
1967-69 Camaro/Firebird, 66-79 Nova Fiberglass Hood Springs-Low Tension
Never have to use a 'prop' rod on your trick looking fiberglass hood again. These lower tension springs will allow you to retain the original workings of your hood. Never ask for help just to get under the hood. These springs...
1967-81 Camaro, 1965-68 Impala, 1947-72 Chevy/GMC truck; Hood Latch Pop-Up Spring
Reproduction hood pop-up spring for 1947-55 and 1962-72 Chevy/GMC truck, 1967-81 Camaro, 1965-68 Impala, Bel Air, Biscayne, Caprice, and 1968 Chevelle, El Camino models. Measures 3-3/4" long and features a black EDP coating...
1967-69 Camaro Cowl Induction Hood Spring; 26 Coils
Reproduction of the original 1969 Camaro cowl induction hood spring. Can also be used for 1967-68 Camaro models with cowl hoods. Manufactured to exact dimensions from premium grade spring steel with a black chromate finish...
Hood Prop Rod For Fiberglass Hood
Hood prop required when installing a fiberglass hood on you Camaro. Since hood springs are not recommended when using fiberglass hoods, this prop is essential for keeping your hood open while working in the engine...
1967 Impala, 1968-69 Camaro; SS Hood Louver Drains; Pair; Made in the USA!
Reproduction of the original Super Sport hood louver drain tubes for use with 1967 Impala SS, and 1968-69 Camaro Super Sport models. These drain tubes install under the hood sub structure and are designed to direct water from...
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 8 Piece Set
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"- 16 x 1" specs....
Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 10-Pieces
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Hood Insulation Fastener; 5/16" Stem Diameter; 3/4" Stem Length; 1-3/4" Head Diameter; 20-Pieces
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most...
1970-2002 GM; Hood Insulation Fastener; Each
Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...
1963-72 Buick, Chevrolet, Oldsmobile, Pontiac; Hood Hinge Spring; For Steel Hoods
Reproduction hood hinge spring for various GM models including Chevelle, Camaro, Impala, Firebird and other various GM models. Each spring is designed and manufactured to exact factory specifications for the models listed...
1965-69 Impala, Camaro, Nova, Firebird; Hood Hinge; RH; Passenger Side
Reproduction of the original hood hinge assembly designed for various GM models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the hood spring when installing a new...
1966-79 GM; Hood Hinge Spring ; Each ; Various Models
Correct replacement hood hinge spring designed for use with various 1966-79 GM models with a standard hood. Each hood hinge spring is manufactured in quality spring steel that matches the OE tension ratio.Sold individually. 2...
1969 Camaro; Hood Latch Release Assembly; Standard or RS Models; EDP Coated
Reproduction of the original hood latch assembly for use with 1969 Camaro standard or Rally Sport models. Each hood release is manufactured to factory specifications featuring the correct latch and spring mechanism. Will bolt...
1958-77 GM; Hood Adjuster Bolt and Nut Set ; 5/16"-18 x 1-3/8"; Various Models
Reproduction of the original hood stop bolt and nut set designed for use on various 1958-77 GM models. This bolt and nut set will keep the hood adjusted to the proper height. These 5/16"-18 x 1-3/8" bolts include the correct...
Fiberglass Hood Springs-Medium Tension
Never have to use a 'prop' rod on your trick looking fiberglass hood again. These medium tension springs will allow you to retain the original workings of your hood. Never ask for help just to get under the hood. These...
1969 Camaro; Hood Lock Catch Support
Reproduction hood lock catch support for 1969 Camaro models. Manufactured in stamped steel to original factory configuration for an authentic appearance and fit. This support is located between the grill and radiator support....
1969-76 Camaro, Corvette, Trans Am; Cowl Induction Solenoid
Reproduction cowl induction solenoid assembly which allows the hood valve assembly to open and shut when the accelerator is depressed. Manufactured to exact specifications, each solonoid will install and function same as...