1967-72; Chevy, GMC C10, C15; Frame Rebuild Starter Kit; with Factory Holes; OE Style; 8 Piece Set
Reproduction LH and RH frame rail set featuring factory-style holes for mounting OE-style brackets, crossmembers, and other original components in their correct factory locations. This high-quality set includes six of the...
1963-70 Chevy and GMC Truck; Tubular Lower Control Arms; Pair
Replacement tubular lower control arms for 1963-70 Chevrolet and GMC 1/2 Ton C10 pickup, panel, and Suburban models. Includes both RH and LH lower control arms with cross shafts, bushings, and ball joints pre-installed. Each...
1963-70 Chevy and GMC C10 Truck; Tubular Upper Control Arms; Pair
Replacement style tubular upper control arms for 1963-70 Chevrolet and GMC truck models. These upper control arms are manufactured from heavy gauge tubular steel. Each control arm is finished in black powdercoat for an...
1959-81 GM; Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for use on various GM models. Manufactured from durable EPDM rubber, this spacer was originally installed to correct uneven ride height on vehicles that did not...
1963-70 Chevrolet C10; Tubular Control Arm Set; Coil Over Type; Upper and Lower
Gain 21st century handling in your classic Chevy C10 truck. This is an upper and lower front tubular control arm set for conversion to coil-over shocks. Each set includes upper and lower tubular control arms, and upper...
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Commonly referred to as a trailing arm, this component mounts between the rear axle housing and the center...
1960-72 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Rear Control Arm; LH Driver Side; EDP Coated
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Also known as a trailing arm, this component mounts between the rear axle housing and the center crossmember to...
1960-72 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Rear Control Arm; RH Passenger Side; EDP Coated
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Also known as a trailing arm, this component mounts between the rear axle housing and the center crossmember to...
Replacement sway bar designed to reduce body roll, under steer, and over steer during cornering, resulting in improved vehicle handling, control, and driving confidence. Engineered to enhance stability without negatively...
1963-70 Chevy Pickup, Blazer, Suburban; Van; Upper Control Arm; C10; Passenger Side
Reproduction of the original upper control arm designed for use with 1963-70 Chevrolet and GMC Pickup, Suburban, Panel Truck, Crew Cab, Blazer and Jimmy 1/2 ton, 2 wheel drive models. Also fits 1970 Chevrolet G10/G20 Van, and...
1963-72 Chevy, GMC C10, C15 Pickup, Suburban; Rear Sway Bar; 1" diameter; with Hardware
Sway bar kit for Chevrolet and GMC truck, pickup, and SUV models. These 1" sway bars reinforce the suspension to deliver improved handling, stability, and overall control. Designed for easy installation using basic hand...
Reproduction front crossmember for 1967-72 Chevrolet and GMC C10 pickup truck models. Each crossmember is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic appearance...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1963-96 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Lower Control Arm Shaft Kit; 2 Wheel Drive
Reproduction control arm shaft kit, precision engineered and rigorously tested to provide a dependable replacement for the original equipment shaft. Designed as a direct fit component, this shaft installs and functions...
1963-72 Chevy, GMC Pickup; C10; C20; C30; Bracket Set; Front Sway Bar to Frame; Stock Height
These 1963-72 front sway bar to frame brackets are designed for a factory/stock height pickup. For trucks with air bag suspension we also recommend using stock height brackets. Sold as a pair to fit LH and RH side of the...
This lowered front sway bar bracket set will provide more ground clearance and is recommended for trucks lowered 3" or more. The brackets pull the bar up towards the frame to achieve additional ground clearance. For trucks...
1960-72 Chevrolet, GMC Pickup Truck; Single Coil Spring Retainer; Upper & Lower; Each
Reproduction of the original single coil spring retainer for 1960-1972 Chevrolet and GMC trucks. Each retainer cup is manufactured from stamped steel to original factory specifications and features the correct contours for an...
1963-72 Chevy, GMC Pickup; C10; C20; C30; Bracket; Front Sway Bar to Frame; Stock Height
This 1963-72 front sway bar to frame bracket is designed for a factory/stock height pickup. For trucks with air bag suspension we also recommend using stock height brackets. Sold individually, fits LH or RH side of the...
This lowered front sway bar bracket will provide more ground clearance and is recommended for trucks lowered 3" or more. The bracket pulls the bar up towards the frame to achieve additional ground clearance. For trucks with...
1967-72 Chevy. GMC C10, C15; Frame Rebuild Starter Kit; without Holes; 8 Piece Set
Reproduction LH and RH frame rail set featuring factory-style holes for mounting OE-style brackets, crossmembers, and other original components in their correct factory locations. This high-quality set includes six of the...
Reproduction RH and LH frame rails for 1967-72 Chevrolet and GMC C10 pickup truck models with short bed. Each frame rail is manufactured to precise factory specifications and includes factory-style holes for mounting OE-style...
Reproduction RH and LH frame rails for 1967-72 Chevrolet and GMC C10 pickup truck models with short bed. Each frame rail is manufactured to precise factory specifications and includes factory-style holes for mounting OE-style...
Reproduction molded rubber front coil spring insulator designed to mount between the coil spring and the frame on various 1949-2002 vehicles. This insulator prevents metal to metal contact, reducing noise, vibration, and...
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Commonly referred to as a trailing arm, this component mounts between the rear axle housing and the center...
1963-70 Chevy Pickup, Blazer, Suburban; Van; Upper Control Arm; C10; Drivers Side
Reproduction of the original upper control arm designed for use with 1963-70 Chevrolet and GMC Pickup, Suburban, Panel Truck, Crew Cab, Blazer and Jimmy 1/2 ton, 2 wheel drive models. Also fits 1970 Chevrolet G10/G20 Van, and...
1963-87 Chevy, GMC C10, C15 Pickup, Suburban; Front Sway Bar; 1-1/8"; with Hardware
Front sway bar for 1963-1987 Chevrolet and GMC pickup truck models. Engineered to reduce body roll, under steer, and over steer during cornering, this sway bar delivers improved stability, more responsive handling, and...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
Reproduction rear crossmember with factory style holes for connecting the LH and RH frame rails at the rear of the frame. A good way to replace a damaged crossmember on a rusty or wrecked truck frame with an original...
1974-78 Mustang II; Front Sway Bar Kit; 3/4" ; 43-1/4" Wide; for Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks equipped with standard width crossmember Mustang II front suspension systems. This sway bar is engineered to reduce body roll, under steer, and over steer during...
Reproduction control arm shaft kit, precision engineered and rigorously tested to deliver a dependable replacement for the original equipment shaft. This direct fit replacement installs and functions exactly like the factory...
1963-70 Chevrolet, GMC Lower Ball Joint; C10; 2 Wheel Drive; 1/2 Ton; RH or LH
Reproduction of the original style lower ball joint for use with 1963-70 Chevrolet and GMC trucks. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about rebuilding your...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
1963-70 Chevrolet, GMC Truck; Upper Ball Joint; 2 WD; C10
Reproduction upper ball joint for 1963-70 Chevrolet and GMC trucks. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about rebuilding your front suspension. You no longer...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4" to 4" inclusive. These heat treated washers are for general purpose and structural use. For use...
Reproduction bracket designed to mount the upper control arm to the frame on 2 wheel drive 1/2 ton Chevrolet and GMC pickup, Blazer, and Jimmy models from 1963-72. Manufactured from heavy duty stamped steel just like the...
Reproduction center transmission mount crossmember with factory style holes for connecting the LH and RH frame rails at the center of the frame and providing a place to mount the transmission. A good way to replace a damaged...
Reproduction front crossmember with factory style holes for connecting the LH and RH frame rails at the front of the frame. Also a good way to save a truck by replacing the damaged crossmember on a rusty or wrecked truck...
Reproduction rear trailing arm mount crossmember with factory style holes for connecting the LH and RH frame rails at the rear of the frame and providing a place to mount the trailing arm braces. A good way to replace a...
1963-72 Chevy, GMC; Pickup, Blazer, Jimmy, Suburban; Upper Control Arm Mount Bracket; LH Driver Side
Reproduction bracket designed to mount the upper control arm to the frame on 2 wheel drive 1/2 ton Chevrolet and GMC pickup, Blazer, and Jimmy models from 1963-72. Manufactured from heavy duty stamped steel just like the...
Reproduction rear axle crossmember with factory style holes for connecting the LH and RH frame rails at the rear of the frame on coil spring trucks. A good way to replace a damaged crossmember on a rusty or wrecked truck...
Reproduction engine mount/control arm mount crossmember with factory style holes for connecting the LH and RH frame rails and mounting the engine and the control arms at the front of the frame. A good way to save a truck by...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...