1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1968-72 Camaro, Impala, Nova; Holley Throttle Cable Bracket
Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1968-70 Camaro, Firebird, Nova, Impala; Fuel Tank Vent Valve
Reproduction of the original gas tank vent valve that's installed on various 1968-70 Buick, Chevrolet, Oldsmobile, and Pontiac models. Manufactured in injection molded plastic to factory specifications. This commonly damaged...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction clips used to mount the fuel line to the frame. Includes six 3/8" clips. Applications: 1967-69 Chevrolet Camaro - Big Block 1967-69 Chevrolet Camaro - Small Block w/4bbl 1965-86 Chevrolet/GMC Truck 1965-70...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1962-81 GM; Fuel Tank Sending Unit Lock Ring; Small; 1-15/16"; Various Models
Correct reproduction fuel tank sending unit locking ring which secures the fuel tank sending unit to the gas tank. Replaces the original ring which are commonly destroyed when being removed. This ring helps to seal the...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1964-71 Chevrolet, GMC; Floor Mounted Accelerator Pedal Pad Trim Plate; Various Car & Truck Models
Correct reproduction accelerator pedal pad stainless trim plate for various 1965-71 GM vehicles. Each trim plate is manufactured in stamped stainless offering long lasting dependability and an authentic appearance. {fitment}...
1969-81 Fuel and Brake Line Clip ; Dual Line 3/8" and 1/4"
Correct clip for attaching fuel and brake lines to the frame on various GM models. This clip is made of galvanized steel and is designed to accept one 3/8" and one 1/4" steel fuel line or one steel brake line. Bolt hole is...
1964-71 Chevrolet; Floor Mounted Accelerator Pedal Pad; Rubber; with Steel Insert; OEM Reproduction
Correct OER® reproduction of the original floor mounted accelerator pedal pad installed on various GM models. Each accelerator pedal pad is manufactured in quality hard EPDM rubber unlike the plastic service replacement...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
Fuel Sending Unit Filter Strainer; For 5/16" Pickup Tube
Correct OER® reproduction of the original fuel tank float strainer designed for use with various 1942-85 GM, Chrysler, Dodge, Plymouth models as listed below. This filter will keep dirt and other elements from clogging or...