Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1968-72 Outer Door Mirror; Chrome: LH; Smooth Style Base; Various GM Models
Reproduction of the original outer door mirror designed for use on various 1968-72 GM models. Each mirror is manufactured in quality die-cast zinc replicating the original mirror in quality and fit. This reproduction mirror...
1962-1977 GM; Windshield Washer Jar Bracket; Various Models
OER® replacement of the original windshield washer jat bracket designed for use on various 1962-77 GM models as listed. This bracket is manufactured in stamped steel and features an EDP coating for rust resistance. This...
1955-82 Spare Tire Hold Down Nut; 5/16"-18 Thread; 3.88" Wide; Zinc Finish
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
1962-72 Chevrolet/Pontiac; OE Style Firewall Pad Fastener; Plastic; 7/16" X 1.50"; Various Models
Correct reproduction plastic firewall pad fastener for various GM models including 1967-69 Camaro, 1967-69 Firebird, 1962-72 Nova and 1962-69 Impala models. These fasteners are required to allow the firewall pad to attach...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1970-81 Camaro, Firebird, 67, 69 Impala, Caprice, Hood Hinge Spring; Each; Various Models
Reproduction of the original hood hinge spring designed for use on various GM vehicles. Each spring is manufactured to replicate the original in quality and design. Will fit and install as original and features OE tension...
1969-87 GM; Door Hinge Repair Set ; Except with 15mm OD Bushings
Reproduction of the original door hinge components for use on various GM models. Repair the broken door hinges with this comprehensive repair set. Each repair kit includes 4 properly hardened shoulder pivot pins and 8...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
1969-70 Full-Size Chevrolet 4 Door Sedan & Station Wagon Tinted Windshield Glass With Antenna
Replacing your original damaged or missing windshield glass will enhance your vehicle's appearance and safety by allowing you to see clearly. Don't settle for anything less than original quality glass when replacing the...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
Reproduction of the original hood hinge assembly designed for use on various 1969 Chevrolet models. Each hood hinge is manufactured in stamped steel to original factory specifications assuring a quality replacement. Finished...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...