Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1965-70 Impala, Electra, LeSabre, Wildcat; Convertible Top Front Header Bow; Various Models
Reproduction of the original convertible top header bow designed for use with various 1965-70 Buick, Chevrolet, Pontiac, Oldsmobile, and Pontiac full size convertible models. Each header bow is manufactured in stamped steel...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Reproduction of the original convertible top cylinder designed for use with 1965-1970 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile full size convertible models. Each cylinder is manufactured from a solid aluminum...
Reproduction of the original front windshield glass for use with 1969-70 Buick, Chevy, Pontiac, Oldsmobile Full Size models as listed. This windshield is manufactured with tempered laminate safety glass that meets the...
Reproduction convertible top latch assembly for 1966-70 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile B-body and C-body convertible models. Manufactured to OE factory specifications, each latch accurately replicates the...
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Reproduction of the original convertible header bow guide pin designed for use with 1965-70 Buick, Chevrolet, Pontiac, and Oldsmobile B-Body full size models. These guide pins are crucial for proper alignment and secure...
1955-72 Buick, Chevy, Pontiac, Oldsmobile, Full Size; Convertible Top Hydraulic Pump Seal Set
Hydraulic pump seal set designed as a direct service replacement for use with various 1955-72 GM full size convertible models. This comprehensive set includes two large O-rings that seal each end of the reservoir (only one...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
1969-70 Chevrolet, Buick, Oldsmobile, Pontiac; Convertible Top Cylinder Shoulder Bolts; Pair
Reproduction bumper jack storage mounts designed for use with 1955-57 Chevrolet full size models. These hard-to-find parts secure the bumper jack properly in the trunk, keeping it stable and in the correct factory location....
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...