Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Reproduction top motor made to provide consistent hydraulic pressure and dependability. Raise and lower the power top with ease. The motor comes complete with rubber mounts. Features original style mounting locations as well...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
OER reproduction of the original front windshield glass for use with 1968-72 Buick, Chevrolet, Pontiac, and Oldsmobile A-Body 2 door coupe models. This windshield is manufactured with tempered laminate safety glass that meets...
Wiper Blade Insert; Replacement; 16" Anco Style; Each
OER reproduction Anco-style windshield wiper blade insert for various classic American vehicle models from the 1960's and up. These 16" wiper blades are manufactured from quality molded rubber as original. Refill is...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
Reproduction door vent glass frame for 1966-67 GM A-Body coupe and convertible models (except El Camino). Manufactured to factory specifications featuring a polished chrome plated finish as original. This frame surrounds the...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1968 Buick, Chevy, Pontiac, Olds Full Size; Door Latch Assembly; 2 Door Models; Drivers Side
Reproduction door latch assembly for various 1968 GM 2 door hardtop, sedan and convertible models. Each door latch assembly is manufactured to factory specifications replicating the original in design and functionality. Will...
16" Windshield Wiper Blade Refill; Pair; 16" x 3/8" wide
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
1968-72 GTO, Chevelle, Monte Carlo, Skylark, Cutlass; Door Window Regulator; Manual; RH
Reproduction window regulator for all 1968 GM A-body models and various 1969-72 A-Body 2-door sedan or wagon models with manually operated door windows. Each regulator is manufactured to replicate the original in quality and...