Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1968-72 Olds F85, Cutlass, 442; 2 Door Hardtop and Sedan; Back Glass; Smoke Gray Tint
This premium reproduction back glass is designed for 1968-72 Oldsmobile F-85, Cutlass, and 442 2 Door Hardtop and Coupe (with post) models. Manufactured in factory-style smoke gray tinted glass to original specifications for...
OER reproduction of the original front windshield glass for use with 1968-72 Buick, Chevrolet, Pontiac, and Oldsmobile A-Body 2 door coupe models. This windshield is manufactured with tempered laminate safety glass that meets...
1964-72 GM Convertible Top Latch Knuckle Hook ; Each
Reproduction of the original latch knuckle hook designed for use on various GM converible models. The knuckle is used to hold the convertible top to the upper windshield header. Screws directly into the convertible top latch...
Reproduction hinge pillar to rocker panel reinforcement panels for 1968-72 Chevelle, El Camino, 1970-72 Monte Carlo and 1971-72 GMC Sprint models. Each panel is manufactured from quality stamped steel to factory...
This premium reproduction RH door glass is designed for 1968 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Manufactured in smoke gray tinted glass to...
This premium reproduction LH door glass is designed for 1968 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, and Pontiac Tempest 2 Door Hardtop and Convertible models. Manufactured in smoke gray tinted glass to...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
Reproduction door vent glass frame for 1966-67 GM A-Body coupe and convertible models (except El Camino). Manufactured to factory specifications featuring a polished chrome plated finish as original. This frame surrounds the...
This premium reproduction RH quarter glass is designed for 1968-1972 Oldsmobile F-85, Cutlass, and 442 2 Door Hardtop models, as well as 1968-1969 Cutlass Supreme 2 Door Hardtop models. Manufactured in factory-style gray...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....