1968 Ford Mustang; Coupe to Fastback Sheet Metal Conversion; w/o Marker Light Indent Kit
If you have a 1968 Ford Mustang Coupe but have always wanted a fastback, this will be your next project. This comprehensive Coupe to Fastback conversion kit supplies you with the necessary sheet metal and braces to convert...
1964-70 Mustang, 1967-68 Cougar; Full Trunk Floor Panel; Coupe, Fastback; EDP Coating
This is the full reproduction stamped steel floor pan assembly to fit 1964-70 Mustang and 1967-68 Cougar in EDP coating. The main structural part begins at the rear seat divider and goes back towards the taillight panel....
1968 Ford Mustang Fastback; Full Quarter Panel; One-Piece; Late Design; RH
Reproduction of the original complete quarter panel designed for use with 1968 Mustang Fastback models (later 1968 models). Each quarter panel is manufactured in stamped steel to original factory specifications featuring...
1967-68 Mustang; Upper Cowl Vent Cover Panel; Right Hand Drive Conversion
Reproduction of the original upper cowl vent cover panel designed for use with 1967-68 Ford Mustang models for use with right hand conversion. Each cowl vent grill panel is manufactured in stamped steel to original factory...
1964-70 Mustang; Complete Trunk Floor Panel; Convertible; EDP Coated
Reproduction of the original floor pan assembly designed for use with 1964-70 Ford Mustang Convertible models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...
1968 Mustang Fastback; Full Quarter Panel; 1-Piece; Early Design; Passenger Side; EDP Coated
Reproduction of the original complete quarter panel designed for use with 1968 Mustang Fastback models (early 1968 models). Each quarter panel is manufactured in stamped steel to original factory specifications featuring...
1967-68 Mustang Fastback; Roof Panel; Silver Weld-Thru Coating
Reproduction of the original roof panel designed for use with 1967-68 Mustang Fastback models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic...
1968 Ford Mustang; Full Quarter Panel; Converible; w/o Side Marker Indent; Passenger Side
Reproduction of the original and complete quarter panel for use with 1968 Mustang convertible models. Each quarter panel is manufactured in stamped steel to factory specifications. This panel is not just an outer skin, but a...
1968 Ford Mustang; Full Quarter Panel; Converible; w/o Side Marker Indent; Drivers Side
Reproduction of the original and complete quarter panel for use with 1968 Mustang convertible models. Each quarter panel is manufactured in stamped steel to factory specifications. This panel is not just an outer skin, but a...
1967-68 Mustang; Door Shell; Drivers Side; EDP Coated
Reproduction of the original style complete door shell for use with 1967-68 Ford Mustang models. Each outer door shell is manufactured in stamped steel to original factory specifications featuring correct contours for an...
1967-68 Mustang; Door Shell; Passenger Side; EDP Coated
Reproduction of the original style complete door shell for use with 1967-68 Ford Mustang models. Each outer door shell is manufactured in stamped steel to original factory specifications featuring correct contours for an...
1964-70 Mustang; Rear Frame Rail; Convertible; Drivers Side; Weld Thru Coated
Reproduction of the original rear frame rail for use with 1964-70 Ford Mustang models. Each frame rail is manufactured to original factory specifications replicating the original in quality, design, and fitment. The rear...
1964-73 Mustang, Cougar; Complete Floor Pan; Convertible
Reproduction of the original complete floor pan designed for use with 1964-73 Ford Mustang and Mercury Cougar convertible models. Each floor pan is manufactured in stamped steel to original factory specifications featuring...
1967-68 Mustang; Steel Dash Panel Assembly; Coupe/Convertible; without Knee Pad Holes
Reproduction stamped steel dash panel assembly for 1967-68 Mustang Coupe (without knee pad holes) or convertible. Features accurate stamping contours, cutouts, and mounting holes for the original dash trim parts to ensure...
1968 Ford Mustang Convertible; Full Quarter Panel; with Side Marker Indent; Passenger Side
Reproduction of the original quarter panel designed for use with 1968 Ford Mustang convertible models with side marker lamp indent. Each quarter panel is manufactured in stamped steel to factory specifications. This panel is...
1967-68 Mustang, Cougar; Lower Cowl Panel; EDP Coated
Reproduction of the original lower cowl panel designed for use with 1967-68 Ford Mustang, and Mercury Cougar models. Each cowl panel is manufactured in stamped steel to original factory specifications featuring correct...
1967-68 Mustang; Hood Assembly; w/o Turn Signal Provisions; Bolt On; EDP Coated
Reproduction of the original hood assembly designed for use with 1967-68 Mustang models without turn signal provision. Each hood panel is manufactured in stamped steel to original factory specifications featuring correct...
1967-68 Mustang; Complete Rear Wheehouse Assembly; Coupe / Fastback; Drivers Side
Reproduction of the complete wheelhouse assembly designed for use with 1967-68 Ford Mustangs. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...
1967-68 Mustang 4 Piece B-Pillar Panel Set; 4 Piece Set
Reproduction B-Pillar panels for 1967-68 Ford Mustang models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic appearance and fit. Replaces the...
1967-68 Mustang; Complete Rear Wheehouse Assembly; Coupe / Fastback; Passenger Side
Reproduction of the complete wheelhouse assembly designed for use with 1967-68 Ford Mustangs. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...
1967-68 Mustang; Racing Front Valance Panel
Fiberglass racing front valance panel for 1967-1968 Mustang models. Each racing valance panel is manufactured in quality fiberglass to the correct configuration. Can be used with stock bumper. Features two parking lamp holes...
1964-70 Ford Mustang; Front To Rear Full Floor Pan Section; Coupe/Fastback; LH
Reproduction of the original Mustang front to rear floor pan section for use with 1964-70 Mustangs. Covers area from 21" behind front seat to just past the area where the floor angles up to meet the firewall. Features all...
1968 Mustang; Quarter Panel Skin; Coupe, Convertible; with Side Marker Recess; Drivers Side
Reproduction of the original style outer quarter panel skin designed for use with 1968 Mustang coupe and convertible models built before 2/15/1968. This reproduction style quarter panel skin replaces the outer sheetmetal from...
1967-68 Ford Mustang; Tail Lamp Panel; No Trunk Corners
Reproduction taillight panel manufactured using heavy gauge stamped steel. Mounts between the quarter panels at the rear of the car and provides a secure mounting point for the taillights and fuel filler pipe. Fits 1967-68...
1964-68 Mustang; 1968-69 Cougar; Front Roof Brace; Coupe / Fastback
Reproduction of the original front hood brace designed for use with 1964-68 Ford Mustang coupe and Fastback models and 1968-69 Mercury Cougar models. Each roof brace is manufactured in stamped steel to original factory...
1968 Mustang; Quarter Panel Skin; Coupe, Convertible; w/o Side Marker Indent; Drivers Side
Reproduction of the original style outer quarter panel skin designed for use with 1968 Mustangs built after 2/15/1968. This reproduction quarter panel skin replaces the outer rear sheetmetal from the door jamb back to the...
1964-70 Ford Mustang; Trunk Floor Pan; EDP Coated; RH
Reproduction of the original style floor pan manufactured in stamped steel for use with 1964-70 Mustangs. Each floor panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...
1964-68 Mustang; Rear Half Floor Section Panel; Passenger Side
Reproduction of the original 1964-68 Mustang complete rear half floor section for RH passenger side side for convertible models. Located behind front seat. Original contour extends under lip of rear seat belt mounting on...
1967-68 Ford Mustang; Quarter Wheelhouse Outer Panel; LH
If your Mustang has only minor rust problems within the wheelhouse area, you may be able to get by with one of these inner or outer wheelhouse panels. More of a patch panel, these pieces can be used to replace small to medium...
1967-68 Ford Mustang; Quarter Wheelhouse Outer Panel; RH
If your Mustang has only minor rust problems within the wheelhouse area, you may be able to get by with one of these inner or outer wheelhouse panels. More of a patch panel, these pieces can be used to replace small to medium...
1964-70 Mustang; Inner Quarter Wheelhouse Panel; Passenger Side; EDP Coated
If your Mustang has only minor rust problems within the wheelhouse area, you may be able to get by with the inner wheelhouse panel. More of a patch panel, this panel can be used to replace small to medium sized areas of rust...
1964-68 Mustang; Rear Half Floor Section Panel; Drivers Side
Reproduction of the original 1964-68 Mustang complete rear half floor section for LH drivers side side for convertible models. Located behind front seat. Original contour extends under lip of rear seat belt mounting on...
1965-70 Mustang; Rear Frame Rail Section; Drivers Side
Reproduction of the original rear frame rail section designed for use with 1965-70 Mustang models. Manufactured to factory specifications out of 14 gauge steel, and measures 28" from the rear end of the frame rail towards the...
1964-70 Mustang; Front Floor Pan; LH Drivers Side; EDP Coated
Reproduction of the original front floor panel for use with 1964-70 Mustang models. Located under and forward of front seat, extending about 5" up toward firewall. This floor panel is cosmetically correct for 1964-1968...
1964-70 Mustang Coupe/Fastback; Rear Trunk Brace Support
Reproduction of the original rear trunk brace support designed for use with 1964-70 Mustang coupe and Fastback models. Each trunk brace support is manufactured in stamped steel to original factory specifications featuring...
1964-70 Mustang; Rear Crossmember Support; EDP Coated
Reproduction rear crossmember support for 1964-1970 Mustang models. Each crossmember support is manufactured in stamped steel to OE specifications. Designed to strengthen the frame and create a rigid structure. Attaches to...
Ford, Lincoln, Mercury Style; Floor Pan Plug; 2-7/8" x 4-5/8"
Galvanized and die stamped steel like the original. Can be used as a universal fit plug on practically any vehicle. The 2-7/8" x 4-5/8" floor pan plugs often need replaced from years of rust damage. Sold individually. Screws...
Ford, Lincoln, Mercury; FLOOR PAN METAL PLUG; Pair; 3-3/4" x 2-3/8"
This is the oval metal plug that seals off the oval hole in the rear footwell area of the floor pan on 1979-1993 Ford Mustang and 1979-86 Mercury Capri. This plug is often rusted or completely missing. Sold individually....
1968 Ford Mustang; Coupe to Fastback Sheet Metal Conversion; w/Marker Light Indent Kit
If you have a 1968 Ford Mustang Coupe but have always wanted a fastback, this will be your next project. This comprehensive Coupe to Fastback conversion kit supplies you with the necessary sheet metal and braces to convert...
1967-68 Mustang Fastback; Steel Dash Panel Assembly; Right Hand Drive
This conversion panel is the perfect solution to a right hand drive conversion, or to replace a dash panel on export models. Reproduction of the original dash panel assembly designed for use with 1967-68 Ford Mustang right...
1967-68 Mustang; Fiberglass Hood; 1967 Shelby Style; Short Style; without Louvers
Reproduction of the 1967 Mustang Shelby style fiberglass hood with dual air inlet scoop, without side louvers. The air scoops are open. Get that Shelby GT350/GT500 look on your stock 1967-68 Mustang. Replaces the stock length...
1964-70 Mustang; Full Trunk Floor Panel; Coupe, Fastback; with Weld-Thru Coating
Quality reproduction of the original trunk floor pan assembly for use with 1964-70 Mustang Fastback and coupe models. Each trunk floor panel is manufactured in stamped steel to original factory specifications featuring...
1964-70 Mustang; Complete Trunk Floor Panel; Convertible; Weld-Thru Coating
This is the full reproduction stamped steel floor pan assembly to fit 1964-70 Mustang Convertible in Weld-Thru primer. The main structural part begins at the rear seat divider and goes back towards the taillight panel....
1968 Ford Mustang Fastback; Full Quarter Panel; One-Piece; Late Design; LH
Reproduction of the original complete quarter panel designed for use with 1968 Mustang Fastback models (later 1968 models). Each quarter panel is manufactured in stamped steel to original factory specifications featuring...
1964-68 Mustang, Cougar; Complete Floor Pan; Coupe & Fastback; EDP Coated
This complete floor pan for 1964-68 Mustang coupe or fastback and 1967-68 Cougar coupe models is manufactured to factory specifications. This stamped steel reproduction floor pan is built as a one-piece design featuring the...
1967-68 Mustang, Cougar; Lower Cowl Panel; with Right Hand Drive; Export
RIGHT HAND DRIVE CONVERSION! Reproduction of the original lower cowl panel designed for use with 1967-68 Mustang and Cougar models with right hand drive. Each cowl panel is manufactured in stamped steel to original factory...
1968 Mustang Fastback; Full Quarter Panel; One-Piece; Early Design; Drivers Side; EDP Coated
Reproduction of the original complete quarter panel designed for use with 1968 Mustang Fastback models (early 1968 models). Each quarter panel is manufactured in stamped steel to original factory specifications featuring...
1967-68 Mustang; Cowl Grill Panel Assembly; 2 Piece Set
Reproduction of the original cowl grill panel assembly designed for use with 1967-68 Ford Mustang models. Each cowl grill panel is manufactured in stamped steel to original factory specifications featuring correct contours...
1967-68 Mustang Fastback; Steel Dash Panel Assembly; with Knee Pad Holes; EDP Coated
Reproduction stamped steel dash panel assembly for 1967-68 Mustang Fastback (with knee pad holes). Features accurate stamping contours, cutouts, and mounting holes for the original dash trim parts to ensure that you have an...
1964-68 Mustang Fastback; Rear Frame Rail Complete; Coupe; Driver Side
Reproduction of the original rear frame rail for use with 1964-68 Ford Mustang coupe models. Each frame rail is manufactured to original factory specifications replicating the original in quality, design, and fitment. This...
1967-68 Mustang; Hood Assembly; w/Turn Signal Cut-Out; Steel; Bolt On; EDP Coated
Reproduction of the original hood assembly designed for use with 1967-68 Mustang models with turn signal provision. Each hood panel is manufactured in stamped steel to original factory specifications featuring correct...
1967-68 Mustang, Cougar; Firewall Panel; Coupe; Fastback; EDP Coating
Reproduction of the original firewall panel for use with 1967-68 Ford Mustang and Mercury Cougar models. Includes the toe board panels along with the entire vertical panel that replaces the old or rusted original....
1968 Ford Mustang Convertible; Full Quarter Panel; with Side Marker Indent; Drivers Side
Reproduction of the original quarter panel designed for use with 1968 Ford Mustang convertible models with side marker lamp indent. Each quarter panel is manufactured in stamped steel to factory specifications. This panel is...
1964-70 Mustang; Rear Frame Rail; Convertible; Passenger Side; Weld Thru Coated
Reproduction of the original rear frame rail for use with 1964-70 Ford Mustang models. Each frame rail is manufactured to original factory specifications replicating the original in quality, design, and fitment. The rear...
1968 Mustang; Tail Lamp Panel; California Special; Stamped Steel; EDP Coated
This is a steel replacement tail lamp panel made specifically for 1968 Mustang running sequential Shelby style (1965 Thunderbird) tail lamps. Will fit any 1968 Mustang as long as the correct Shelby style tail lamps are used....
1968 Ford Mustang; Full Quarter Panel; Coupe; w/o Side Marker Indent; Drivers Side
Reproduction of the original and complete quarter panel for use with 1968 Mustang coupe models. Each quarter panel is manufactured in stamped steel to factory specifications. This panel is not just an outer skin, but a...
1968 Ford Mustang; Full Quarter Panel; Coupe; w/o Side Marker Indent; Passenger Side
Reproduction of the original and complete quarter panel for use with 1968 Mustang coupe models. Each quarter panel is manufactured in stamped steel to factory specifications. This panel is not just an outer skin, but a...
1967-68 Mustang; Complete Wheelhouse Assembly; Convertible; Passenger Side; EDP Coated
Reproduction of the original complete wheelhouse assembly designed for use with 1967-68 Mustang convertible models. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct...
1967-68 Mustang; Complete Wheelhouse Assembly; Convertible; Drivers Side; EDP Coated
Reproduction of the original complete wheelhouse assembly designed for use with 1967-68 Mustang convertible models. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct...
1964-70 Mustang; Seat Platform; Convertible; One Piece Design
Reproduction of the original seat platform designed for use with 1964-70 Ford Mustang convertible models. Each seat platform is manufactured in stamped steel to original factory specifications featuring correct contours for...