Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1964-68 Ford Mustang; Fuel Tank Sending Unit; without Low Fuel Warning; 5/16"
Reproduction fuel tank sending unit for 1964-68 Ford Mustangs and other various models. The most accurate reproduction fuel tank sending unit in the industry, with original design brass float and filter. This unit monitors...
1968 Ford Galaxie, Custom, LTD; Fuel Tank Filler Neck Pipe; For 25 Gallon Tank
Reproduction fuel filler neck pipe for 1968 Ford Galaxie and full size passenger car models. Connects with a fuel filler hose (sold separately) to the fuel tank. Replacing the filler neck is recommended whenever you replace...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1948-86 Ford; Fuel Tank Sending Unit Brass Float; Various Models
Reproduction of the original style and correct brass float for use with various 1948-86 Ford and Mercury models as listed below. This sending unit brass float is desirable for its long-lasting dependability as it lasts much...
Reproduction fuel level sending unit for 1966-69 Ford Fairlane, 1968-69 Torino and 1966-69 Mercury Comet models with 3/8" inlet. This direct fit replacement includes the NBR float, locking ring, and O-ring. Does NOT fit...
1966-96 Ford, Mercury; Lower Fuel Tank Filler Pipe Seal; Various Models
Reproduction of the original fuel tank to filler pipe seal designed for use on various1966-97 Ford and Mercury applications. Each seal is manufactured to correct factory specifications and replaces the old or missing original...
1966-76 Ford Bronco; Rear Main Fuel Tank Mounting Strap; Each
Reproduction of the original style side mount gas tank strap designed for use with 1966-1976 Ford Bronco models. Each strap is manufafactured in stamped steel to correct factory dimensions. Comes with a black EDP coating for...
1966-69 Ford; Filler Neck-to-Body Sealing Gasket
Gas tank filler neck-to-body sealing gasket. Made of rubber, this gasket sits behing the filler neck flange to cushion the fuel filler where it mounts to the body of the car. Fits various 1966-69 Fairlane, Falcon, and...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1966-76 Ford Bronco; Gas Tank Pipe Filler Guard Set
Reproduction gas tank filler pipe guard set for 1966-76 Ford Bronco. These panels install in the driver side inner quarter area and cover the filler pipe that extend through the bedfloor and out the quarter panel. They are...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1967-70 Ford Mustang; Rubber Filler Neck Hose; Fuel Tank to Filler Pipe; 4-7/8" Long; 2-3/16" id
Reproduction fuel filler hose that seals the inlet filler neck to the fuel tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...
1965-73 Ford Mustang; Screw Set; Gas Tank Mounting; 13 Piece Set
This 13 piece set contains all the mounting hardware needed to install your gas fuel tank. Each piece is factory correct. Screws and bolts are all fabricated from heavy-duty steel and coated to prevent any corrosion. Ford...
1968-70 Ford Galaxie, Custom, LTD; Fuel Tank Filler Neck Pipe
Reproduction fuel filler neck pipe for 1968-70 Ford Galaxie and full size passenger car models. Connects with a fuel filler hose (sold separately) to the fuel tank. Replacing the filler neck is recommended whenever you...
1966-76 Ford Bronco; Fuel Tank Filler Pipe; For Auxiliary (side) Tank
Reproduction of the front auxiliary fuel tank filler pipe for 1966-76 Ford Bronco models. Replacing the filler neck is recommended whenever you replace your gas tank. This is where the gas cap attaches. After years of use and...
Stainless steel reproduction of the fuel tank sending unit featuring the original design with a brass float, O-ring, and filter that replicate the original in appearance and functionality. This unit monitors the fuel level in...
1966-1977 Ford Bronco; Auxiliary Fuel Tank Mounting Straps; Pair
Reproduction of the original style rear mount gas tank straps designed for use with 1966-1977 Ford Bronco models. Each strap is manufafactured in stamped steel to correct factory dimensions. Comes with a black EDP coating for...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...