Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1963-72; Chevrolet Bow Tie Outer Door Mirror; with Mounting Hardware
Reproduction outer door mirror for various 1967-72 Chevrolet models. Each mirror is manufactured in die-cast zinc to factory specifications. Will fit and install as original. Features the Bow Tie emblem engraved on the rear...
1962-1977 GM; Windshield Washer Jar Bracket; Various Models
OER® replacement of the original windshield washer jat bracket designed for use on various 1962-77 GM models as listed. This bracket is manufactured in stamped steel and features an EDP coating for rust resistance. This...
1962-72 Chevrolet/Pontiac; OE Style Firewall Pad Fastener; Plastic; 7/16" X 1.50"; Various Models
Correct reproduction plastic firewall pad fastener for various GM models including 1967-69 Camaro, 1967-69 Firebird, 1962-72 Nova and 1962-69 Impala models. These fasteners are required to allow the firewall pad to attach...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1966-74 GM; Outer Door Mirror; Round; with Ribbed Base; Hardware Included; "Show Quality"
Reproduction of the original outer door mirror designed for use with various 1966-74 GM models. Original style replacement outer door mirror manufactured in high quality zinc die-cast with excellent chrome finish. Each mirror...
1959-80 Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Brand New Reproduction wiper motor built using the industry's most advanced engineering technology. Core shortages and low availability have made our brand new replacement wiper motors the high quality, low cost alternative...
1968-72 Chevrolet Chevelle, El Camino; Front Fender; Skirt; Pair
Reproduction plastic inner fender wells/skirts for 1968-72 Chevrolet Chevelle and El Camino. Made in correct black semi-gloss ABS plastic and have a similar finish to the OEM. Made in the U.S.A. Sold in pairs. Made in USA...
1968-79 Hood Hinge Assembly ; RH ; Various Models
Reproduction of the original hood hinge assembly designed for use on various 1968-79 GM models. Each hood hinge is manufactured from heavy duty stamped steel assuring a quality replacement. We recommend replacing the hood...
OER reproduction of the original front windshield glass for use with 1968-72 Buick, Chevrolet, Pontiac, and Oldsmobile A-Body 2 door coupe models. This windshield is manufactured with tempered laminate safety glass that meets...
Wiper Blade Insert; Replacement; 16" Anco Style; Each
OER reproduction Anco-style windshield wiper blade insert for various classic American vehicle models from the 1960's and up. These 16" wiper blades are manufactured from quality molded rubber as original. Refill is...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
1969 Chevrolet Chevelle, El Camino; Front Bumper Bracket Set; 4 Pieces
Reproduction front bumper bracket set for 1968 Chevelle and El Camino makes replacing your damaged or rusted bumper and bumper components easier. Correct stamped steel brackets with all the proper mounting holes in correct...