Headlamp Adjusting Screw ; For GM Models ; 1/4"-28 x 2"
Reproduction of the headlamp adjustment screw required for a wide variety of GM models including 1965-75 Impala, Biscayne, Bel Air and Caprice models. This 1/4"-28 adjustment screw comes zinc plated for corrosion resistance...
1962-71 GM Headlight 1/4"-28 x 1" Adjustment Screw with Nylon Nut
Original self-retaining nylon nut and 1/4"-28 x 1" screw assembly used for headlamp beam adjustment on 1962-71 GM models. This nut and screw mounts directly to the headlamp housing to enable the headlamp beam to be aimed...
OER® reproduction of the original headlamp adjusting spring designed for use on various GM models. This headlamp spring is used to adjust the headlight beam to the proper alignment. Applications: 1973-1974 Buick Apollo...
1967-68 Camaro, 1968 Chevelle, El Camino; Headlight Bezel Nut Set ; Set of 10
Reproduction of the original style barrel nuts designed for use on 1967-68 Camaro models. These unique barrel shaped plastic insert nuts press into the steel frame and provide a secure anchor for the trim screws. These...
1968 Camaro; Rally Sport Outer Headlight Door Cover; with Chrome Trim; LH Driver Side
Correct reproduction of the original headlamp return cover (outer door) installed on all 1968 Camaro Rally Sport models. Manufactured in quality injection molded ABS replicating the original in quality and design. This return...
1968 Camaro; RS Headlamp Bell Crank Spring and Bracket Set ; 8 Piece Set
Keys onto lower end of headlamp bell crank and acts as an over center counter balance assist. This set includes two attachment brackets which install on the lower edge of the headlamp housing and allow correct closure of the...
1967-69 Camaro; Rally Sport Headlamp Hinge Pivot Bolt; Each
Reproduction of the original bolt used to pivot the Rally Sport headlamp doors on 1967-69 Camaro models. This bolt installs through the control opening hinge and attaches the hinge to the headlamp housing on RS (hidden...
1968 Camaro; Rally Sport; Headlight Bellcrank; LH Drivers Side
Reproduction of the original 1968 Camaro Rally Sport bellcrank. The bellcrank installs from the headlamp actuator to the main headlamp housing assembly and enables the headlamp door to open and close when activated. Includes...
Screw #8 X 1" with #6 Phillips Head Tapping Screws; Chrome; Set of 4
Set of 4 screws used to attach various parts including 1974-78 Mustang II headlamp bezels # 13064P.
1967-68 Camaro/1962-68 Chevrolet Truck; Headlamp Adjuster Set
Reproduction headlamp adjuster set for 1967-68 Camaro and 1962-68 Chevrolet truck models. Each set has the 4 adjusting screws and nuts and the 2 springs, enough for both headlamps. Chevrolet Applications: 1967-68 Camaro...
1968-69 RS Headlamp Bellcrank Bushings ; 4 piece set
Reproduction of the original headlamp bellcrank bushings designed for use on 1968-69 RS Camaros with the hidden headlamp option. The bushings for on the upper and lower bellcranks. Manufactured with injection molded tooling...
1962-68 GM Headlight Adjustment Screw with Nylon Nut 1/4"-28 x 1-1/2"
Original self-retaining nylon nut and 1/4"-28 x 1-1/2" screw assembly used for headlamp beam adjustment on 1962-68 GM models. This nut and screw mounts directly to the headlamp housing to enable the headlamp beam to be aimed...
1/4"-28 GM Headlamp Adjuster Nylon Nut
This headlamp adjusting nut mounts directly to the headlamp housing and enables the headlamp beam to be aimed correctly on 1965-75 Impala/Full Size, 1967-77 Camaro and a wide variety of other GM models. White nylon nut is...
1967-69 Camaro; Rally Sport; Headlight Hinge Bolt Set; Short; Set of 3
Reproduction of the original one-piece, shouldered stud headlight bolts designed for use on 1967-69 Rally Sport Camaros. This set includes 3 hinge bolts which are used to mount the control opening hinge to the control arm...
1/4-28 GM Headlamp Adjuster Nylon Nut
Reproduction 1/4-28 x 1-1/2" headlamp adjuster nylon nut for a wide variety of classic GM vehicles. Will fit various early GM vehicles, including 1967-68 Firebird models. Sold individually. Buick Applications: 1962-68 Full...
1968 Camaro; Rally Sport Outer Headlight Door Cover; with Chrome Trim; RH Passenger Side
Correct reproduction of the original headlamp return cover (outer door) installed on all 1968 Camaro Rally Sport models. Manufactured in quality injection molded ABS replicating the original in quality and design. This return...
1967-68 Camaro RS; Headlamp Door Screw Set; 8 Piece
Reproduction of the correct screw set designed to install the black outer headlamp door to the rear headlamp backing plate. Manufactured in black oxide that matches the original GM screw, this phillips head reproduction is...
1968 Camaro; Rally Sport; Headlight Bellcrank; RH Passenger Side
Reproduction of the original 1968 Camaro Rally Sport bellcrank. The bellcrank installs from the headlamp actuator to the main headlamp housing assembly and enables the headlamp door to open and close when activated. Includes...
1967-69 Camaro; RS Headlight Hinge to Housing Bushing; Each
Reproduction of the original style bushing that's part of the 1967-69 Camaro RS hidden headlamp hardware. This special bushing is designed to hold the headlight hinge to the headlight housing. 2 required per housing. 4...
1968-69 Camaro; Raly Sport Headlight Vacuum Relay Valve Assembly
Quality reproduction of the original GM headlight relay switch assembly designed for use on 1968-69 Chevrolet Camaro models with Rally Sport (hidden headlight) option. The relay works with the headlight switch on RS models to...
1968-69 Camaro; Rally Sport Headlamp Pin & Clevis Set
Reproduction of the original pin and clevis set designed for use with 1968-69 Camaro RS models with hidden headlamps. The pin and clevis is required to hold the headlight vacuum actuator to the bracket. This is a high quality...
1968 Camaro; Rally Sport Headlight Actuator Bracket; Large, Rear; LH Driver Side
Reproduction of the original headlight actuator support bracket designed for use with 1968 Camaro models with the Rally Sport (hidden headlight) option. This bracket supports the rear portion of the headlamp actuator canister...
1968-69 Camaro; Rally Sport Headlight Bushing Set; 22 Piece Set
Reproduction of the original bushings needed when rebuilding or adding a Rally Sport grill assembly (concealed headlamps). If your rebuilding a 1968-69 Rally Sport headlamp assembly, then you'll want to replace the upper and...
1967-68 Camaro RS; Headlamp Door Molding Rivets; 10 piece set
Reproduction of the original headlamp door molding hardware for use on 1967-68 Camaro RS models. These original style reproduction rivets fasten the outer headlamp door molding to the headlamp door. 5 rivets required per side...
1967-68 Camaro; Rally Sport Headlight Door Hinge; RH or LH; Each
Reproduction of the original RS Camaro headlight hinge that pivots the headlamp concealment door assembly when the headlights are activated. Manufactured in OEM zinc die-cast material. Hinge was installed on both the LH and...
1968 Camaro RS; Headlamp Bellcrank Shaft & Lever Supports; RH or LH; Pair
Reproduction of the original headlamp bellcrank shaft and lever support designed for use on 1968 Camaro RS models. These supports are used to support the shaft and lever assembly for the headlamps on RS (hidden headlamp)...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head, 10 Piece Set
Original style oval head chrome screw set designed to install sill plates and other various components and parts. Includes 10 chrome phillips oval head #8 x 3/4" screws. Set includes 10 phillips oval head screws. Use as...
Screw Set; Chrome Plated ; #8 x 3/4" Oval Phillips Head ; Set of 8 ;
Original style oval head chrome screw set designed to install sill plates, headlamp bezels, shift plates and other various components and parts. Includes 8 chrome phillips oval head #8 x 3/4" screws. Use as required. Can be...
1968-69 Camaro RS Headlamp Vacuum Actuator; with Concealed Headlights; Each
Superb quality reproduction of the original headlamp vacuum canister designed for use on all 1968-69 Camaro models that included concealed headlamps. Each actuator is manufactured to exact factory specifications ensuring a...
# 8 x 3/4" Oval Phillips Head Screw; Black Oxide; #8 Head
Original style oval head black-oxide screw originally used to install moldings, grill and headlamp bezels, and various other components and parts on classic American cars and trucks. Sold individually. Use as required. Can be...
1968 Camaro; Rally Sport Headlight Hose Set; with Color Hoses; Diagram Included
OER® reproduction of the original vacuum hose set designed for use on 1968 RS Camaro models. This reproduction hose kit is designed and manufactured to exact factory specifications including correct size vacuum hoses and...
1968-69 Camaro; Rally Sport Firewall Grommet; EPDM Molded Rubber
Reproduction of the original firewall grommet designed for use with 1968-69 Chevrolet Camaro models equipped with the Rally Sport hidden headlight option. Manufactured from high-quality EPDM rubber, this grommet accurately...
1967-68 Camaro; Rally Sport Headlight Backing Plate; RH Passenger Side
Reproduction of the original rear headlamp backing plate designed for use on 1967-68 Camaros with the RS (hidden headlamp) option. This backing plate acts as a support for the outer headlamp door and molding. This backing...
1968-69 RS Headlamp Retracting Cover Shaft Washer - Each
Reproduction of the original retracting cover shft washer unit designed for use with 1968-69 headlamp assemblies. This washer is designed to replace the existing unit for any 1969-69 Camaro RS model when rebuilding the...
1967-69 RS Headlight Hinge to Headlight Backing Plate Spacer ; Each
Reproduction of the original retracting cover mounting plate found on 1967-69 Camaro Rally Sport models. This reproduction spacer is manufactured in injection molded ABS offering an authentic appearance and fit. Used as a...