1968-69 Camaro SS; Hood Louver Set; with Hardware; Pair; "Show Quality"
Reproduction of the original die-cast hood louvers designed for use with all 1968-69 Camaro Super Sport models equipped with a 350 or 396 engine. Manufactured with OER® exclusive tooling to exact factory specifications....
1967-69 Camaro/Firebird, 66-79 Nova Fiberglass Hood Springs-Low Tension
Never have to use a 'prop' rod on your trick looking fiberglass hood again. These lower tension springs will allow you to retain the original workings of your hood. Never ask for help just to get under the hood. These springs...
1967-81 Camaro, 1965-68 Impala, 1947-72 Chevy/GMC truck; Hood Latch Pop-Up Spring
Reproduction hood pop-up spring for 1947-55 and 1962-72 Chevy/GMC truck, 1967-81 Camaro, 1965-68 Impala, Bel Air, Biscayne, Caprice, and 1968 Chevelle, El Camino models. Measures 3-3/4" long and features a black EDP coating...
Hood Prop Rod For Fiberglass Hood
Hood prop required when installing a fiberglass hood on you Camaro. Since hood springs are not recommended when using fiberglass hoods, this prop is essential for keeping your hood open while working in the engine...
1967 Impala, 1968-69 Camaro; SS Hood Louver Drains; Pair; Made in the USA!
Reproduction of the original Super Sport hood louver drain tubes for use with 1967 Impala SS, and 1968-69 Camaro Super Sport models. These drain tubes install under the hood sub structure and are designed to direct water from...
1963-72 Buick, Chevrolet, Oldsmobile, Pontiac; Hood Hinge Spring; For Steel Hoods
Reproduction hood hinge spring for various GM models including Chevelle, Camaro, Impala, Firebird and other various GM models. Each spring is designed and manufactured to exact factory specifications for the models listed...
1966-79 GM; Hood Hinge Spring ; Each ; Various Models
Correct replacement hood hinge spring designed for use with various 1966-79 GM models with a standard hood. Each hood hinge spring is manufactured in quality spring steel that matches the OE tension ratio.Sold individually. 2...
1958-77 GM; Hood Adjuster Bolt and Nut Set ; 5/16"-18 x 1-3/8"; Various Models
Reproduction of the original hood stop bolt and nut set designed for use on various 1958-77 GM models. This bolt and nut set will keep the hood adjusted to the proper height. These 5/16"-18 x 1-3/8" bolts include the correct...
Fiberglass Hood Springs-Medium Tension
Never have to use a 'prop' rod on your trick looking fiberglass hood again. These medium tension springs will allow you to retain the original workings of your hood. Never ask for help just to get under the hood. These...
Reproduction hood pin rubber gasket found on models with hood pins. Each gasket is die-cut to proper dimension. Will also fit a wide variety of aftermarket hood pins. Sold individually. Use as required. Check measurements...
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1958-77 Buick, Chevy, Olds, Pontiac; Hood Adjust Bumper and Screw Set ; Various Models
Reproduction hood adjustment bumpers for various 1958-77 GM models including 1967-69 Camaro and Firebird models. These 7/8" OD reproduction stoppers and screws are manufactured to original specifications to replace the worn...
1967-72 Hood Louver Gasket ; Each ; Camaro ; Nova
Reproduction of the original hood louver gaskets that seals the hood louvers to the hood. These special gaskets are manufactured to precisely replace the old or worn originals. Prevents water and other elements from seeping...
1965-1970 GM; Hood Insulation Fastener Set; 20 Piece Set; Various Models
Reproduction of the original hood insulation fasteners designed for various 1965-69 GM models. Manufactured in injection molded ABS plastic to replace OE part number # 3909199. These are an exact copy of the OE retainer for...
1965-81 Hood Latch Pilot Bolt; 4"
OER® reproduction of the 4" hood latch pilot bolt for use on various GM models as listed below. The bolt is designed to attach to the lock plate retainer. Once installed, the hood pop up spring surrounds this bolt....
1967-69 Camaro, Firebird; Plastic Clip Set; Radiator Support To Hood Seal; 9 Piece Set
Reproduction of the radiator support to hood seal clip set designed for 1967-69 Camaro and Firebird models with air conditioning. Each clip is injection molded to original specifications. Clips are designed to hold the hood...
1966-1979 Camaro, Impala, Nova; Rubber Side Hood Bumper ; Each
Reproduction of the original style side hood rubber bumper designed for use various GM models. Over time, the rubber stoppers on your hood can wear out or deteriorate. These reproduction stoppers will help keep your hood...
1967-81 Camaro Hood Latch Assembly ; Chrome ; Pre-Assembled
OER® reproduction of the original style hood safty latch assembly designed for use on 1967-81 Chevrolet Camaro models. Each assembly is manufactured in stamped steel replicating the original design. This reproduction...
1967-81 Camaro Hood Latch Assembly ; Black ; Pre-Assembled
OER® reproduction of the original style hood safty latch assembly designed for use on 1967-81 Chevrolet Camaro models. Each assembly is manufactured in stamped steel replicating the original design. This reproduction...