1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl
Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1968-69 327, 350 Carb to Accelerator Lever Rod; Small Block with 4 bbl Carb
Reproduction 1968-69 accelerator pedal rod for 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...
1964-71 Chevrolet, GMC; Floor Mounted Accelerator Pedal Pad Trim Plate; Various Models
Correct reproduction accelerator pedal pad stainless trim plate for various 1965-71 GM vehicles. Each trim plate is manufactured in stamped stainless offering long lasting dependability and an authentic appearance. {fitment}...
1968-72 Camaro, Impala, Nova; Holley Throttle Cable Bracket
Reproduction of the original style Holley throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
1964-71 Chevrolet; Floor Mounted Accelerator Pedal Pad; EPDM Rubber with Steel Insert
Correct OER® reproduction of the original floor mounted accelerator pedal pad installed on various GM models. Each accelerator pedal pad is manufactured in quality hard EPDM rubber unlike the plastic service replacement...
1968-74 Accelerator Pedal Pad To Rod Support
Reproduction of the original accelerator pedal rod support for use on the various applications listed. Each support is manufactured in injection molded ABS offering an exact replacement of the original. Applications:...
1958-71 GM; Accelerator Pedal Ball Stud Pivot; 1/4"-20 x 1-1/2"; Various Models
Original factory ball stud pivot designed for use on various GM models. 1/4"-20 x 1-1/2". Accelerator pedal ball studs can break after many years of use and will need to be replaced. Check your stud for wear when replacing...
1968-69 396 Carb to Accelerator Lever Rod ; Big Block with 4 bbl Carb
Reproduction of the original 1968-69 accelerator pedal rod designed for use with 396 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is...
1968-72 Camaro, Impala, Nova; Quadrajet Throttle Cable Bracket
Reproduction of the original style Quadrajet throttle cable bracket designed for use with various 1968-72 Chevrolet models. Each cable bracket is manufactured in stamped steel to original factory specifications making this...
Powerglide Upper Kickdown Clip
OER® Authorized reproduction upper kickdown clip for models with powerglide automatic transmission. Connects the upper passing gear kickdown rod to the bellcrank assembly. Applications: 1967-69 Camaro with Powerglide...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...